C3225X5R1C226M View Datasheet(PDF) - Orister Corporation
Part Name
Description
Manufacturer
C3225X5R1C226M Datasheet PDF : 10 Pages
| |||
Page No. : 6/10
The selected inductance rather than the core size for a fixed inductor value is the key for actual core loss. As the inductance
increases, core losses decrease. Unfortunately, increase of the inductance requires more turns of wire and therefore the
copper losses will increase.
Ferrite designs are preferred at high switching frequency due to the characteristics of very low core losses. So, design goals
can focus on the reduction of copper loss and the saturation prevention.
Ferrite core material saturates “hard”, which means that inductance collapses abruptly when the peak design current is
exceeded. The previous situation results in an abrupt increase in inductor ripple current and consequent output voltage
ripple.
Do not allow the core to saturate! Different core materials and shapes will change the size/ current and price/current
relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy materials are small and do not radiate energy. However, they are usually
more expensive than the similar powdered iron inductors. The rule for inductor choice mainly depends on the price vs. size
requirement and any radiated field/EMI requirements.
CIN and COUT Selection
The input capacitance, CIN, is needed to filter the trapezoidal current at the source of the high side MOSFET. To prevent large
ripple current, a low ESR input capacitor sized for the maximum RMS current should be used. The RMS current is given by：
IRMS = IOUT (MAX ) ⋅VOUT ⋅ VIN − 1
VIN VOUT
This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst‐case condition is commonly used for design
because even significant deviations do not offer much relief.
Choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or
height requirements in the design.
For the input capacitor, a 10μF x 2 low ESR ceramic capacitor is recommended. For the recommended capacitor, please refer
to table 3 for more detail. The selection of COUT is determined by the required ESR to minimize voltage ripple.
Moreover, the amount of bulk capacitance is also a key for COUT selection to ensure that the control loop is stable. Loop
stability can be checked by viewing the load transient response as described in a later section. The output ripple, ΔVOUT , is
determined by：
ΔVOUT
≤ ΔIL ⋅ ⎢⎣⎡ESR
+1
8 fCOUT
⎤
⎥⎦
The output ripple will be highest at the maximum input voltage since ΔIL increases with input voltage. Multiple capacitors
placed in parallel may be needed to meet the ESR and RMS current handling requirement. Dry tantalum, special polymer,
aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Special polymer capacitors offer
very low ESR value. However, it provides lower capacitance density than other types. Although Tantalum capacitors have the
highest capacitance density, it is important to only use types that pass the surge test for use in switching power supplies.
Aluminum electrolytic capacitors have significantly higher ESR. However, it can be used in cost‐sensitive applications for
ripple current rating and long term reliability considerations. Ceramic capacitors have excellent low ESR characteristics but
can have a high voltage coefficient and audible piezoelectric effects. The high Q of ceramic capacitors with trace inductance
can also lead to significant ringing.
Higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high
voltage rating and low ESR make them ideal for switching regulator applications. However, care must be taken when these
capacitors are used at input and output. When a ceramic capacitor is used at the input and the power is supplied by a wall
adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to
the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially
cause a voltage spike at VIN large enough to damage the part.
DS‐RS6516‐05 February, 2010
www.Orister.com
|
|
Share Link: 