5962-9755701HPC View Datasheet(PDF) - Broadcom Corporation
Part Name
Description
Manufacturer
5962-9755701HPC Datasheet PDF : 16 Pages
| |||
ACPL-785E, HCPL-7850, HCPL-7851, 5962-97557
Data Sheet
DC Electrical Specifications
DC Electrical Specifications
Over recommended operating conditions (TA = –55°C to +125°C, VIN+ = 0V, VIN– = 0V, VDD1 = 5V and VDD2 = 5V, unless otherwise
specified).
Parameter
Symbol Group Aa Min
Subgroups
Typb
Max
Unit
Test Conditions
Fig Notes
Input Offset Voltage
VOS
Gain
G
20-mV Nonlinearity
10-mV Nonlinearity
NL200
NL100
Output Common-Mode Voltage
Input Supply Current
Output Supply Current
Input-Output Insulation
Leakage Current
VOCM
IDD1
IDD2
II–O
Maximum Input Voltage Before
Output Clipping
|VIN+|
MAX
Average Input Bias Current
Average Input Resistance
Input DC Common-Mode
Rejection Ratio
IIN
RIN
CMRRIN
Output Resistance
Output Low Voltage
Output High Voltage
Output Short-Circuit Current
RO
VOL
VOH
|IOSC|
Resistance (Input-Output)
RI–O
Capacitance (Input–Output)
CI–O
1, 2 ,3
2, 3
1
2, 3
1
2, 3
1
1, 2, 3
1, 2, 3
1, 2, 3
1
–1.0 0.6 5.0 mV
7.36 8.00 8.64 V/V
7.60 8.00 8.4
— 0.05 0.8
%
— 0.05 0.2
— 0.01 0.2
— 0.01 0.1
2.20 2.56 2.80 V
— 10.7 15.5 mA
— 9.4 17 mA
—
—
1.0 μA
— 320 — mV
— –0.57 — μA
— 480 — kΩ
—
69
—
dB
—
1
—
Ω
— 1.28 —
V
— 3.84 —
V
—
11
— mA
—
1012
—
Ω
—
2.7
—
pF
4.5V ≤ (VDD1, VDD2) ≤ 5.5V 1, 2, 3 c
–200 mV ≤ VIN+ ≤ 200 mV,
4.5V ≤ (VDD1, VDD2) ≤ 5.5V
5, 6, 7
–200 mV ≤ VIN+ ≤ 200 mV, 5, 8, 9, d
4.5V ≤ (VDD1, VDD2) ≤ 5.5V 10, 12
–100 mV ≤ VIN+ ≤ 100 mV,
4.5V ≤ (VDD1, VDD2) ≤ 5.5V
–400 mV ≤ VIN+ ≤ 400 mV,
4.5V ≤ (VDD1, VDD2) ≤ 5.5V
5, 8, 9,
11, 12
14, 16
15, 16
RH ≤ 65%, t = 5 sec.
e
VI–O = 1500 Vdc, TA = 25°C
4, 12
13
f
g
VIN+ = 400 mV
VIN+ = –400 mV
VOUT = 0V or VDD2
VI–O = 500 Vdc
f = 1 MHz, VI–O = 0 Vdc
4
h
i
e
a. Commercial parts receive 100% testing at 25°C (Subgroups 1 and 9). SMD, Class H and Class E receive 100% testing at 25, 125, and –55°C (Subgroups 1 and 9,
2 and 10, 3 and 11, respectively).
b. All typicals are at the nominal operating conditions of VIN+ = 0V, VIN– = 0V, TA = 25°C, VDD1 = 5V and VDD2 = 5V.
c. Exact offset value is dependent on layout of external bypass capacitors. The offset value in the data sheet corresponds to Broadcom’s recommended layout
(see Figure 26 and Figure 27).
d. Nonlinearity is defined as half of the peak-to-peak output deviation from the best-fit gain line, expressed as a percentage of the full-scale differential output
voltage.
e. Device considered a two-terminal device: Pins 1, 2, 3, and 4 are shorted together, and pins 5, 6, 7, and 8 are shorted together.
f. Because of the switched capacitor nature of the sigma-delta A/D converter, time averaged values are shown.
g. CMRRIN is defined as the ratio of the gain for differential inputs applied between pins 2 and 3 to the gain for both common-mode inputs applied to both pins
2 and 3 with respect to pin 4.
h. When the differential input signal exceeds approximately 320 mV, the outputs will limit at the typical values shown.
i. Short-circuit current is the amount of output current generated when either output is shorted to VDD2 or ground. Broadcom does not recommend operations
under these conditions.
Broadcom
-5-
|
|
Share Link: 