DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

M1025-11I-155.5200 View Datasheet(PDF) - Integrated Circuit Systems

Part Name
Description
Manufacturer
M1025-11I-155.5200
ICST
Integrated Circuit Systems ICST
M1025-11I-155.5200 Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Integrated
Circuit
Systems, Inc.
Input Reference Clocks
Two clock reference inputs and a selection mux are
provided. Either reference clock input can accept a
differential clock signal (such as LVPECL or LVDS) or
a single-ended clock input (LVCMOS or LVTTL on the
non-inverting input).
A single-ended reference clock on the unselected
reference input can cause an increase in output
clock jitter. For this reason, differential reference
inputs are preferred; interference from a differential
input on the non-selected input is minimal.
Implementation of single-ended input has been
facilitated by biasing nDIF_REF0 and nDEF_REF1 to Vcc/2,
with 50kto Vcc and 50kto ground. Figure 4 shows
the input clock structure and how it is used with either
LVCMOS / LVTTL inputs or a DC- coupled LVPECL
clock.
DIF_REF0
LVCMOS/
LVTTL
VCC
MUX
50k
nDIF_REF0
50k
0
X
VCC
50k
DIF_REF1 127
1
LVPECL
VCC
82
127
VCC
50k
50k
nDIF_REF1
82
50k
REF_SEL
M1025/26
Figure 4: Input Reference Clocks
Differential LVPECL Inputs
Differential LVPECL inputs are connected to both
reference input pins in the usual manner. The external
load termination resistors shown in Figure 4 (the 127
and 82resistors) will work for both AC and DC
coupled LVPECL reference clock lines. These provide
the 50load termination and the VTT bias voltage.
Single-ended Inputs
Single-ended inputs (LVCMOS or LVTTL) are
connected to the non-inverting reference input pin
(DIF_REF0 or DIF_REF1). The inverting reference input pin
(nDIF_REF0 or nDIF_REF1) must be left unconnected.
In single-ended operation, when the unused inverting
input pin (nDIF_REF0 or nDEF_REF1) is left floating (not
connected), the input will self-bias at VCC/2.
M1025/26
VCSO BASED CLOCK PLL WITH AUTOSWITCH
Product Data Sheet
PLL Operation
The M1025/26 is a complete clock PLL. It uses a phase
detector and configurable dividers to synchronize the
output of the VCSO with the selected reference clock.
The “M” divider divides the VCSO output frequency,
feeding the result into the plus input of the phase
detector. The output of the “R” divider is fed into the
minus input of the phase detector. The phase detector
compares its two inputs. The phase detector output,
filtered externally, causes the VCSO to increase or
decrease in speed as needed to phase- and
frequency-lock the VCSO to the reference input.
The value of the M divider directly affects closed loop
bandwidth.
The relationship between the nominal VCSO center
frequency (Fvcso), the M divider, the R divider, and the
input reference frequency (Fin) is:
Fvcso
=
Fin
×
M---
R
For the available M divider and R divider look-up table
combinations, Tables 3 and 4 on pg. 3 list the Total PLL
Ratio as well as Fin when using the M1025-11-155.5200 or
the M1026-11-155.5200. (“Ordering Information”, pg. 14.)
Due to the narrow tuning range of the VCSO
(+200ppm), appropriate selection of all of the following
are required for the PLL be able to lock: VCSO center
frequency, input frequency, and divider selections.
Post-PLL Divider
The M1025/26 features a post-PLL (P) divider. By using
the P Divider, the device’s output frequency (Fout) can
be the VCSO center frequency (Fvcso) or 1/2 Fvcso.
The P_SEL pin selects the value for the P divider: logic 1
sets P to 2, logic 0 sets P to 1. (See Table 5 on pg. 4.)
When the P divider is included, the complete relation-
ship for the output frequency (Fout) is defined as:
Fout = --F----v---c---s---o---- = Fin × ------M-----------
P
R× P
Due to the narrow tuning range of the VCSO
(+200ppm), appropriate selection of all of the following
are required for the PLL be able to lock: VCSO center
frequency, input frequency, and divider selections.
M1025/26 Datasheet Rev 1.0
5 of 14
Revised 28Jul2004
Integrated Circuit Systems, Inc. Networking & Communications www.icst.com tel (508) 852-5400
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]