Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

D100E View Datasheet(PDF) - MicroPower Direct, LLC

Part Name
Description
Manufacturer
D100E Datasheet PDF : 2 Pages
1 2
Model Selection Guide
Model
Number
D101E
D102E
D103E
D104E
D105E
D106E
D107E
D108E
D111E
D112E
D113E
D114E
D115E
D116E
D117E
D118E
D121E
D122E
D123E
D124E
D125E
D126E
D127E
D128E
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
278
30
5
4.5 - 5.5
270
30
5
4.5 - 5.5
260
30
5
4.5 - 5.5
253
30
5
4.5 - 5.5
278
30
5
4.5 - 5.5
267
30
5
4.5 - 5.5
256
30
5
4.5 - 5.5
253
30
12 10.8 - 13.2 114
15
12 10.8 - 13.2 111
15
12 10.8 - 13.2 105
15
12 10.8 - 13.2 104
15
12 10.8 - 13.2 113
15
12 10.8 - 13.2 110
15
12 10.8 - 13.2 105
15
12 10.8 - 13.2 104
15
24 21.6 - 26.4 56
8
24 21.6 - 26.4 55
8
24 21.6 - 26.4 52
8
24 21.6 - 26.4 51
8
24 21.6 - 26.4 56
8
24 21.6 - 26.4 55
8
24 21.6 - 26.4 52
8
24 21.6 - 26.4 51
8
Voltage
(VDC)
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
5.0
9.0
12.0
15.0
±5.0
±9.0
±12.0
±15.0
Output
Current
(mA, Max)
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
200.0
111.0
83.0
67.0
±100.0
±56.0
±42.0
±33.0
Current
(mA, Min)
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
20.0
12.0
9.0
7.0
±10.0
±6.0
±5.0
±4.0
Load
Regulation
(%, Max)
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Other input/output combinations are available
(i.e. 3.3 VDC). Contact the factory for details at:
sales@micropowerdirect.com
Derating Curve
Efficiency
(%, Typ)
72
74
77
79
72
75
78
79
73
75
79
80
74
76
79
80
74
76
80
81
74
76
80
81
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters will operate without external components. However,
when measuring output ripple, it is recommended that an external
ceramic capacitor
be placed from the
+Vout pin to the
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
-Vout pin for single
output units and
from each output
to common for dual
output units. An in-
5 VDC
12 VDC
24 VDC
4.7 μF
2.2 μF
1.0 μF
5 VDC
9 VDC
12 VDC
15 VDC
10.0 μF
4.7 μF
2.2 μF
1.0 μF
4.7 μF
2.2 μF
1.0 μF
0.47 μF
put capacitor will enhance stability over temperature and input line
variations. Recommended capacitor values are given in the table above.
For applications requiring very low output noise levels, a simple LC filter
should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30
VDC output. To do this, connect the load across the positive (+Vout) and
negative (-Vout) outputs and float the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin Single Dual
Pin
1 +Vin +Vin
5
2 -Vin -Vin
6
4 -Vout -Vout
Single
No Pin
+Vout
Dual
Common
+Vout
Mechanical Dimensions
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com
Direct download click here

 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]