Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

P5200 View Datasheet(PDF) - Conexant Systems

Part NameDescriptionManufacturer
P5200 AccessRunner™ ADSL-USB Modem Device Set Conexant
Conexant Systems Conexant
P5200 Datasheet PDF : 56 Pages
First Prev 31 32 33 34 35 36 37 38 39 40 Next Last
AccessRunner ADSL-USB Modem Device Set Data Sheet
Signal Name
R_INTER_SUPERB 31
R_INTER_DATA
32
R_FAST_SUPERB 33
R_FAST_FRAMEB 34
R_CLK_LS0
47
R_CLK_LS1
49
R_DAT_AS1
42
R_DAT_LS0
48
R_DAT_LS1
50
R_NCO_AS1
40
R_NCO_LS0
37
R_NCO_LS1
38
CLIPB
84
T_INTER_BYTEB
5
T_FAST_BYTEB
4
T_CLK_AS0
6
T_DAT_AS1
12
T_DAT_AS0
7
T_CLK_LS1
13
T_DAT_LS1
14
TXSOC1
21
LTR
81
NTR
8
NTR_CTL
29
BIT_CLOCK
17
NOTES:
I/O Types: See Table 3-8.
Table 3-7. CX11627 ADDP Hardware Signal Definitions (Continued)
Pin
I/O
I/O Type
Signal Name/Description
NOT USED
O
O
Receive Interleaved Data Bit Output Superframe Qualifier. Not
used; leave open.
O
O
Receive Interleaved Data Bit Output. Clocked at BIT_CLOCK rate.
O
O
Receive Fast Data Bit Output Superframe Qualifier. Not used;
leave open.
O
O
Receive Fast Data Bit Output Frame Qualifier. Not used; leave
open.
I
I
Receive Data Clock (LS0). Not used; leave open.
I
I
Receive Data Clock (LS1). Not used; leave open.
O
O
Receive Data (AS1). Not used; leave open.
O
O
Receive Data (LS0). Not used; leave open.
O
O
Receive Data (LS1). Not used; leave open.
O
O
Receive NCO (AS1). Not used; leave open.
O
O
Receive NCO (LS0). Not used; leave open.
O
O
Receive NCO (LS1). Not used; leave open.
O
O
Clip Interrupt. This status output goes low for one ADC_CLK clock
cycle whenever clipping is detected. This signal can be for monitoring
incoming data for saturation. Not used; leave open.
O
O
Transmit Interleaved Data Bit Input Enable. Not used; leave open.
O
O
Transmit Fast Data Bit Input Enable. Not used; leave open.
I
I
Transmit Data Clock (AS1). Not used; leave open.
I
I
Transmit Data (AS1). Not used; leave open.
I
I
Transmit Data (AS0). Not used; leave open.
I/O
I/O
Transmit Data Clock (LS1). Not used; leave open.
I
I
Transmit Data (LS1). Not used; leave open.
I
I
TC1 Block Transmit Start of Cell. Not used; leave open.
O
O
8 kHz Local Timing Reference. Not used; leave open.
I/O
I/O
8 kHz Network Timing Reference. Not used; leave open.
I
I
Network Timing Reference I/O Control. Not used; leave open.
O
O
Serial Data Bit Clock Output. Used to synchronize the serial input
and output data bit streams, enables, and superframe qualifiers. Not
used; leave open.
100427B
Conexant
3-15
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2020  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]