ADUCM410 View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADUCM410

Precision Analog Microcontroller, 16-Bit Analog Input/Output with MDIO Interface, Arm Cortex-M33

Analog Devices 

Data Sheet

Pin No. Mnemonic

B1

P0.3/IRQ0/CS0/PLACLK0/PLAI3

B2

P0.2/MOSI0/PLACLK1/PLAI2

B3

P2.3/BM/PLAI10

B4

SWCLK

B5

RESET

B6

VDAC1

B7

VREF

B8

AVDD

C1

IOVDD1

C2

P0.1/MISO0/COMOUT1/PLAI1

C3

P0.0/SCLK0/COMOUT0/PLAI0

C4

P1.0/SIN1/COMOUT2/PLAI4

C5

P2.2/POR/CLKOUT/SWO

C6

AIN14/COM3P/BUF0_VREF

C7

AIN2/PADC0P

ADuCM410

Type1

I/O

I/O

I/O

I

I

AO

AO/AI

S

S

I/O

I/O

I/O

I/O

AI/AO

AI

Description

Digital Input/Output Port 0.3 (P0.3).

External Interrupt 0 (IRQ0).

SPI0 Chip Select (CS0).

PLA Clock 0 (PLACLK0).

Input to PLA Element 3 (PLAI3).

Ball B1 is a multilevel voltage input/output with 3.3 V, 1.8 V, or 1.2 V

support. Note that 3.3 V is the default.

Digital Input/Output Port 0.2 (P0.2).

SPI0 Master Out, Slave In (MOSI0).

PLA Clock 1 (PLACLK1).

Input to PLA Element 2 (PLAI2).

Ball B2 is a multilevel voltage input/output with 3.3 V, 1.8 V, or 1.2 V

support. Note that 3.3 V is the default.

Digital Input/Output Port 2.3 (P2.3). An internal pull-up resistor is

enabled at power-up on P2.3.

Boot Mode (BM). This pin determines the start-up sequence after every

reset.

Input to PLA Element 10 (PLAI10).

Serial Wire Debug Clock.

Reset Input (Active Low). An internal pull-up resistor is included with this pin.

Voltage DAC 1 Output.

0.92 V Reference with a 100 nF Capacitor.

3.3 V Analog Power Supply.

1.2 V/1.8 V GPIO Supply. If unused, IOVDD1 can be tied to DVDD_REG or

to DGND.

Digital Input/Output Port 0.1 (P0.1).

SPI 0 Master Input, Slave Output (MISO0).

Comparator 1 Output (COMOUT1)

Input to PLA Element 1 (PLAI1).

Ball C2 is a multilevel voltage input/output with 3.3 V, 1.8 V, or 1.2 V

support. Note that 3.3 V is the default.

Digital Input/Output Port 0.0 (P0.0).

SPI 0 Clock (SCLK0).

Comparator 0 Output (COMOUT0).

Input to PLA Element 0 (PLAI0).

Ball C3 is a multilevel voltage input/output with 3.3 V, 1.8 V, or 1.2 V

support. Note that 3.3 V is the default.

Digital Input/Output Port 1.0 (P1.0).

UART Input 1 (SIN1).

Comparator 2 Output (COMOUT2).

Input to PLA Element 4 (PLAI4).

Ball C4 is a multilevel voltage input/output with 3.3 V, 1.8 V, or 1.2 V

support. Note that 3.3 V is the default.

Digital Input/Output Port 2.2 (P2.2).

Reset Output (POR). This pin function is an output, and it is the default.

Clock Output (CLKOUT).

Serial Wire Debug (SWD) Output (SWO).

Analog Input 14 (AIN14).

Comparator 3 Emitter Voltage (VE) Positive (COM3P).

Buffered Reference Voltage source (BUF0_VREF).

Analog Input 2 (AIN2).

PGA Channel 0 Positive (PADC0P).

Rev. A | Page 25 of 35

Share Link: