MDF7-20P-2.54DS View Datasheet(PDF) - HIROSE ELECTRIC
Part Name
Description
Manufacturer
MDF7-20P-2.54DS Datasheet PDF : 7 Pages
| |||
sDouble-Row Straight Pin Header
qBoard Through-hole Diameter: Ø1.0++00.1
[Specific No.] –* *, (* *)
Blank :Gold plated
(01) :Tin plated
qMDF7 (Board to Board Size: 2.54 to 5.5mm)
qMDF7P (Board to Board Size: 2.54 to 8mm)
Unit: mm
Unit: mm
Part Number
CL No. Number of Contacts A
B
C
Part Number
CL No. Number of Contacts A
B
C
MDF7-12DP-2.54DSA(**) 547-0034-7-**
12
15.24 12.7 10 MDF7P-12DP-2.54DSA(**) 547-0407-2-**
12
15.24 12.7 12.5
MDF7-14DP-2.54DSA(**) 547-0365-4-**
14
17.78 15.24 10 MDF7P-14DP-2.54DSA(**) –––––––
14
17.78 15.24 12.5
MDF7-16DP-2.54DSA(**) 547-0364-1-**
16
20.32 17.78 10 MDF7P-16DP-2.54DSA(**) 547-0367-0-**
16
20.32 17.78 12.5
MDF7-20DP-2.54DSA(**) 547-0114-4-**
20
25.4 22.86 10 MDF7P-20DP-2.54DSA(**) 547-0260-6-**
20
25.4 22.86 12.5
MDF7-22DP-2.54DSA(**) 547-0093-6-**
22
27.94 25.4 10 MDF7P-22DP-2.54DSA(**) 547-0261-9-**
22
27.94 25.4 12.5
MDF7-24DP-2.54DSA(**) 547-0250-2-**
24
30.48 27.94 10 MDF7P-24DP-2.54DSA(**) 547-0262-1-**
24
30.48 27.94 12.5
MDF7-26DP-2.54DSA(**) 547-0251-5-**
26
33.02 30.48 10 MDF7P-26DP-2.54DSA(**) 547-0263-4-**
26
33.02 30.48 12.5
MDF7-30DP-2.54DSA(**) 547-0037-5-**
30
38.1 35.56 10 MDF7P-30DP-2.54DSA(**) 547-0264-7-**
30
38.1 35.56 12.5
MDF7-34DP-2.54DSA(**) 547-0252-8-**
34
43.18 40.64 10 MDF7P-34DP-2.54DSA(**) –––––––
34
43.18 40.64 12.5
MDF7-40DP-2.54DSA(**) 547-0253-0-**
40
50.8 48.26 10 MDF7P-40DP-2.54DSA(**) –––––––
40
50.8 48.26 12.5
MDF7-46DP-2.54DSA(**) 547-0254-3-**
46
58.42 55.88 10 MDF7P-46DP-2.54DSA(**) –––––––
46
58.42 55.88 12.5
Note 1: The board to board size in the above table represents the state where the 1.6mm thickness board is used.
Note 2: A quantity for delivery is determined per pack (100 pcs.). If needed, please order the products per pack.
Note 3: The MDF7 series 2-row plating specification is different from the single-row plating specification. No-specification indicates the
gold plating, and (01) indicates the tin plating.
Note 4: As for the products, which HRS No. is not indicated in the above table, we will correspond to samples, and mass-production
according to your demand. Please contact HRS company, as required.
BApplication Pattern and PCB mounting pattern
qWhen the double-row straight pin header is used
BPrecautions
1. Recommended Soldering Condition sFlow Condition by Automatic Soldering Unit
Soldering temperature: 250±5ç, Soldering time: within 2 seconds
sManual Soldering Condition
Soldering iron temperature: 290±10ç, Soldering time: within 2 seconds
2. Board Masking
If the automatic soldering unit is used, block the pin header through-hole on the receptacle
mounted board with the masking tape, etc., and prevent the flux pervasion.
In addition, if much flux is adhered so as to affect the contact, please be sure to clean the board.
3. Cleaning Condition
Refer to Nylon Connector Use Hand book.
4. Cautions
sIt is impossible to fix the board to the board by the connector only. Please take actions
to fix the board without using the connector.
sIf the board deformation could occur due to vibration, please use the gold plating.
sDon't use the connector as the top entry.
A253
|
|
Share Link: 