MC74VHCT244AN View Datasheet(PDF) - ON Semiconductor
Part Name
Description
Manufacturer
MC74VHCT244AN Datasheet PDF : 6 Pages
| |||
MC74VHCT244A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ DC ELECTRICAL CHARACTERISTICS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Symbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ICCT
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ IOPD
Parameter
Quiescent Supply
Current
Output Leakage
Current
Test Conditions
Per Input: VIN = 3.4V
Other Input: VCC or GND
VOUT = 5.5V
VCC
V
5.5
0
TA = 25°C
Min
Typ
Max
1.35
0.5
TA = – 40 to 85°C
Min
Max Unit
1.50 mA
5.0
µA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0ns)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Symbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tPLH,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tPHL
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tPZL,
tPZH
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tPLZ,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tPHZ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tOSLH,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ tOSHL
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Cin
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Cout
Parameter
Maximum Propagation Delay
A to YA or B to YB
Output Enable Time
OEA to YA or OEB to YB
Output Disable Time
OEA to YA or OEB to YB
Output to Output Skew
Maximum Input Capacitance
Maximum Three–State Output
Capacitance (Output in
High–Impedance State)
Test Conditions
VCC = 5.0 ± 0.5V
VCC = 5.0 ± 0.5V
RL = 1kΩ
VCC = 5.0 ± 0.5V
RL = 1kΩ
VCC = 5.0 ± 0.5V
(Note NO TAG)
CL = 15pF
CL = 50pF
CL = 15pF
CL = 50pF
CL = 50pF
CL = 50pF
TA = 25°C
Min
Typ
Max
5.4
7.4
5.9
8.4
7.7
10.4
8.2
11.4
8.8
11.4
1.0
4
10
9
TA = – 40 to 85°C
Min
Max Unit
1.0
8.5
ns
1.0
9.5
1.0
12.0 ns
1.0
13.0
1.0
13.0 ns
1.0
pF
10
pF
pF
Typical @ 25°C, VCC = 5.0V
CPD Power Dissipation Capacitance (Note NO TAG)
18
pF
1. Parameter guaranteed by design. tOSLH = |tPLHm – tPLHn|, tOSHL = |tPHLm – tPHLn|.
2. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC / 8 (per bit). CPD is used to determine the no–load
dynamic power consumption; PD = CPD VCC2 fin + ICC VCC.
NOISE CHARACTERISTICS (Input tr = tf = 3.0ns, CL = 50pF, VCC = 5.0V)
Symbol
VOLP
VOLV
VIHD
VILD
Parameter
Quiet Output Maximum Dynamic VOL
Quiet Output Minimum Dynamic VOL
Minimum High Level Dynamic Input Voltage
Maximum Low Level Dynamic Input Voltage
TA = 25°C
Typ
Max
Unit
0.9
1.1
V
– 0.9
– 1.1
V
2.0
V
0.8
V
VHC Data – Advanced CMOS Logic
3
DL203 — Rev 1
MOTOROLA
|
|
Share Link: 