PSP-500 View Datasheet(PDF) - RSG Electronic Components GmbH
Part Name
Description
Manufacturer
PSP-500 Datasheet PDF : 5 Pages
| |||
RSG■
ELECTRONIC COMPONENTS
RSG Electronic Components GmbH ■ Sprendlinger Landstr. 115 ■ D-63069 Offenbach/Germany
Tel. +49 69 984047-0 ■ Fax +49 69 984047-77 ■ info@rsg-electronic.de ■ www.rsg-electronic.de
Änderungen vorbehalten / subject to change without notice
500W with PFC and Parallel Function
PSP-500 series
Features :
Universal AC input / Full range
Built-in active PFC function, PF>0.95
Protections:Short circuit/Over load/Over voltage/Over temperature
Foced air cooling by built-in DC fan
Current sharing up to 2000W(3+1)
With power good and fail signal output
Built-in remote ON-OFF control
Built-in remote sense function
3 years warranty
SPECIFICATION
MODEL
PSP-500-5
PSP-500-12 PSP-500-13.5 PSP-500-15 PSP-500-24 PSP-500-27 PSP-500-48
OUTPUT
INPUT
DC VOLTAGE
5V
12V
13.5V
15V
24V
27V
RATED CURRENT
80A
41.5A
37A
33A
20.8A
18.5A
CURRENT RANGE
0 ~ 80A
0 ~ 41.5A
0 ~ 37A
0 ~ 33A
0 ~ 20.8A
0 ~ 18.5A
RATED POWER
400W
498W
499.5W
495W
499.2W
499.5W
RIPPLE & NOISE (max.) Note.2 100mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
150mVp-p
VOLTAGE ADJ. RANGE
4.75 ~ 5.5V
10 ~ 13.2V
12 ~ 15V
13.5 ~ 18V
20 ~ 26.4V
24 ~ 30V
VOLTAGE TOLERANCE Note.3 2.0%
1.0%
1.0%
1.0%
1.0%
1.0%
LINE REGULATION
0.5%
0.3%
0.3%
0.3%
0.2%
0.2%
LOAD REGULATION
2.0%
0.5%
0.5%
0.5%
0.5%
0.5%
SETUP, RISE TIME
1500ms, 50ms at full load
HOLD TIME (Typ.)
24ms at full load
VOLTAGE RANGE Note.6 90 ~ 264VAC 127 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
0.95/230VAC 0.98/100VAC at full load
EFFICIENCY (Typ.)
76%
82%
82%
82%
84%
84%
AC CURRENT (Typ.)
7A/115AVC 3.5A/230VAC
INRUSH CURRENT (Typ.) 20A/115VAC 40A/230VAC
LEAKAGE CURRENT
<1mA / 240VAC
OVER LOAD
110 ~ 125% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
48V
10.5A
0 ~ 10.5A
504W
200mVp-p
41 ~ 56V
1.0%
0.2%
0.5%
86%
PROTECTION OVER VOLTAGE
5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V
Protection type : Shut down o/p voltage, re-power on to recover
27.6 ~ 32.4V 31 ~ 36.5V
57.6 ~ 67.2V
OVER TEMPERATURE
RTH2 95 Detect on heatsink of Q1,Q7 power transistor & L3 output choke
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION REMOTE CONTROL
RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off sink current <4 ~ 10mA
WORKING TEMP.
-10 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY
20 ~ 90% RH with 30CFM forced air non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.03%/ (0 ~ 50
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 Approved
WITHSTAND VOLTAGE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
SAFETY & ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMC
(Note 4)
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A
MTBF
130.1K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
278*129*63.5mm (L*W*H)
PACKING
2.6Kg; 6pcs/15.7Kg/0.89CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. In parallel connection, maybe only one unit operated, if the total output load less than 5% of rated load condition.
6. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name:PSP-500-SPEC 2006-04-13
|
|
Share Link: 