74VCXH245WM(1999) View Datasheet(PDF) - Fairchild Semiconductor
Part Name
Description
Manufacturer
74VCXH245WM Datasheet PDF : 8 Pages
| |||
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC)
DC Input Voltage (VI)
T/R, OE
−0.5V to +4.6V
−0.5V to +4.6V
I/O Ports
−0.5V to VCC+ 0.5V
DC Output Voltage (VO)(Note 2)
−0.5V to VCC + 0.5V
DC Input Diode Current (IIK) VI < 0V
−50 mA
DC Output Diode Current (IOK)
VO < 0V
−50 mA
VO > VCC
+50 mA
DC Output Source/Sink Current
(IOH/IOL)
DC VCC or Ground Current
Storage Temperature (TSTG)
±50 mA
±100 mA
−65°C to +150°C
Recommended Operating
Conditions (Note 3)
Power Supply
Operating
1.65V to 3.6V
Data Retention Only
1.2V to 3.6V
Input Voltage
Output Voltage (VO)
Output Current in IOH/IOL
VCC = 3.0V to 3.6V
VCC = 2.3V to 2.7V
VCC = 1.65V to 2.3V
Free Air Operating Temperature (TA)
Minimum Input Edge Rate (∆t/∆V)
−0.3V to VCC
0V to VCC
±24 mA
±18 mA
±6 mA
−40°C to +85°C
VIN = 0.8V to 2.0V, VCC = 3.0V
10 ns/V
Note 1: The Absolute Maximum Ratings are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the Absolute Maximum Rat-
ings. The “Recommended Operating Conditions” table will define the condi-
tions for actual device operation.
Note 2: IO Absolute Maximum Rating must be observed.
Note 3: Floating or unused control inputs must be held HIGH or LOW.
DC Electrical Characteristics (2.7V < VCC ≤ 3.6V)
Symbol
Parameter
Conditions
VIH
HIGH Level Input Voltage
VIL
LOW Level Input Voltage
VOH
HIGH Level Output Voltage
VOL
LOW Level Output Voltage
II
II(HOLD)
II(OD)
Input Leakage Current
Bushold Input Minimum
Drive Hold Current
Bushold Input Over-Drive
Current to Change State
IOH = −100 µA
IOH = −12 mA
IOH = −18 mA
IOH = −24 mA
IOL = 100 µA
IOL = 12 mA
IOL = 18 mA
IOL = 24 mA
VIN = VCC or GND
VIN = 0.8V
VIN = 2.0V
(Note 4)
(Note 5)
IOZ
3-STATE Output Leakage
VO = VCC or GND
VI = VIH or VIL
ICC
Quiescent Supply Current
VI = VCC or GND
∆ICC
Increase in ICC per Input
VIH = VCC −0.6V
Note 4: An external driver must source at least the specified current to switch from LOW-to-HIGH.
Note 5: An external driver must sink at least the specified current to switch from HIGH-to-LOW.
VCC
(V)
2.7–3.6
2.7–3.6
2.7–3.6
2.7
3.0
3.0
2.7–3.6
2.7
3.0
3.0
2.7–3.6
3.0
3.0
3.6
3.6
2.7–3.6
Min
2.0
VCC − 0.2
2.2
2.4
2.2
75
−75
450
−450
2.7–3.6
2.7–3.6
Max
0.8
0.2
0.4
0.4
0.55
±5.0
±10
20
750
Units
V
V
V
V
µA
µA
µA
µA
µA
µA
3
www.fairchildsemi.com
|
|
Share Link: 