AD8004AR-14 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
AD8004AR-14 Datasheet PDF : 16 Pages
| |||
AD8004
ABSOLUTE MAXIMUM RATINGS1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V
Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . Note 2
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 2.5 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range (N, Q, R) . . . . –65°C to +125°C
Operating Temperature Range
A Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
S Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2Specification is for device in free air:
14-Lead PDIP Package: θJA = 90°C/W, θJC = 30°C/W
14-Lead SOIC Package: θJA = 140°C/W, θJC = 30°C/W
14-Lead CERDIP Package: θJA = 110°C/W, θJC = 30°C/W
ORDERING GUIDE
Model
Temperature
Range
Package
Description
Package
Option
AD8004AN
– 40°C to +85°C 14-Lead PDIP
AD8004AR-14
– 40°C to +85°C 14-Lead SOIC
AD8004AR-14-REEL – 40°C to +85°C 13" Tape and Reel
AD8004AR-14-REEL7 – 40°C to +85°C 7" Tape and Reel
AD8004SQ
– 55°C to +125°C 14-Lead CERDIP
N-14
R-14
R-14
R-14
Q-14
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8004 is limited by the associated rise in junction temperature.
The maximum safe junction temperature for plastic encapsu-
lated devices is determined by the glass transition temperature
of the plastic, approximately +150°C. Exceeding this limit
temporarily may cause a shift in parametric performance due to
a change in the stresses exerted on the die by the package.
Exceeding a junction temperature of +175°C for an extended
period can result in device failure.
While the AD8004 is internally short circuit protected, this may
not be sufficient to guarantee that the maximum junction tem-
perature is not exceeded under all conditions. To ensure proper
operation, it is necessary to observe the maximum power ratings.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8004 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
604⍀
604⍀
50⍀
SCOPE
INPUT
50⍀
VIN
50⍀
+VS
0.1F
10F
0.1F
10F
–VS
Figure 3. Test Circuit; Gain = –2
249⍀
VIN
61.9⍀
499⍀
50⍀
SCOPE
INPUT
50⍀
+VS
0.1F
10F
0.1F
10F
–VS
Figure 4. Test Circuit; Gain = –2
–4–
REV. C
|
|
Share Link: 