Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

ADXL210 View Datasheet(PDF) - Analog Devices

Part NameADXL210 ADI
Analog Devices ADI
DescriptionLow Cost ±2 g/±10 g Dual Axis iMEMS® Accelerometers with Digital Output
ADXL210 Datasheet PDF : 11 Pages
1 2 3 4 5 6 7 8 9 10
ADXL202/ADXL210–SPECIFICATIONS (TA = TMIN to TMAX, TA = +25؇C for J Grade only, VDD = +5 V,
RSET = 125 k, Acceleration = 0 g, unless otherwise noted)
Parameter
SENSOR INPUT
Measurement Range1
Nonlinearity
Alignment Error2
Alignment Error
Transverse Sensitivity3
Conditions
Each Axis
Best Fit Straight Line
X Sensor to Y Sensor
ADXL202/JQC/AQC
ADXL210/JQC/AQC
Min
Typ Max Min
Typ Max
± 1.5
±2
0.2
±1
± 0.01
±2
±8
± 10
0.2
±1
± 0.01
±2
Units
g
% of FS
Degrees
Degrees
%
SENSITIVITY
Duty Cycle per g
Sensitivity, Analog Output
Temperature Drift4
Each Axis
T1/T2 @ +25°C
10
At Pins XFILT, YFILT
from +25°C
12.5 15
3.2
312
± 0.5
4.0 4.8
100
± 0.5
%/g
mV/g
% Rdg
ZERO g BIAS LEVEL
0 g Duty Cycle
Initial Offset
0 g Duty Cycle vs. Supply
0 g Offset vs. Temperature4
E NOISE PERFORMANCE
Noise Density5
FREQUENCY RESPONSE
3 dB Bandwidth
T 3 dB Bandwidth
Sensor Resonant Frequency
FILTER
E RFILT Tolerance
Minimum Capacitance
SELF TEST
L Duty Cycle Change
DUTY CYCLE OUTPUT STAGE
FSET
FSET Tolerance
O Output High Voltage
Output Low Voltage
T2 Drift vs. Temperature
Rise/Fall Time
S POWER SUPPLY
Operating Voltage Range
Specified Performance
Quiescent Supply Current
B Turn-On Time6
TEMPERATURE RANGE
Operating Range
O Specified Performance
Each Axis
T1/T2
from +25°C
@ +25°C
Duty Cycle Output
At Pins XFILT, YFILT
32 kNominal
At XFILT, YFILT
Self-Test “0” to “1”
RSET = 125 k
I = 25 µA
I = 25 µA
To 99%
JQC
AQC
25
50 75
42
50 58
±2
±2
1.0 4.0
1.0 4.0
2.0
2.0
500 1000
500 1000
500
500
5
5
10
14
± 15
1000
± 15
1000
10
10
125 M/RSET
0.7
1.3
VS – 200 mV
200
35
200
125 M/RSET
0.7
1.3
VS – 200 mV
200
35
200
3.0
5.25
4.75
5.25
0.6 1.0
160 CFILT + 0.3
2.7
5.25
4.75
5.25
0.6 1.0
160 CFILT + 0.3
0
+70 0
+70
–40
+85 –40
+85
%
g
%/V
mg/°C
µg/Hz
Hz
kHz
kHz
%
pF
%
kHz
mV
mV
ppm/°C
ns
V
V
mA
ms
°C
°C
NOTES
1For all combinations of offset and sensitivity variation.
2Alignment error is specified as the angle between the true and indicated axis of sensitivity.
3Transverse sensitivity is the algebraic sum of the alignment and the inherent sensitivity errors.
4Specification refers to the maximum change in parameter from its initial at +25 °C to its worst case value at TMIN to TMAX.
5Noise density (µg/Hz) is the average noise at any frequency in the bandwidth of the part.
6CFILT in µF. Addition of filter capacitor will increase turn on time. Please see the Application section on power cycling.
All min and max specifications are guaranteed. Typical specifications are not tested or guaranteed.
Specifications subject to change without notice.
–2–
REV. B
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]