Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

0402F104F101CR View Datasheet(PDF) - Unspecified

Part Name0402F104F101CR ETC
Unspecified 
DescriptionMULTILAYER CERAMIC CAPACITORS - General Purpose Series (10V to 100V)
0402F104F101CR Datasheet PDF : 17 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Approval sheet
General Purpose Capacitors
No.
Item
Test Condition
Requirements
8. Vibration Resistance * Vibration frequency: 10~55 Hz/min.
* No remarkable damage.
* Total amplitude: 1.5mm
* Cap change and Q/D.F.: To meet initial spec.
* Test time: 6 hrs. (Two hrs each in three mutually
perpendicular directions.)
9. Solderability
* Solder temperature: 235±5°C
95% min. coverage of all metalized area.
* Dipping time: 2±0.5 sec.
10. Bending Test
* The middle part of substrate shall be pressurized by * No remarkable damage.
means of the pressurizing rod at a rate of about 1 mm per * Cap change
second until the deflection becomes 1 mm and then the
pressure shall be maintained for 5±1 sec.
* Measurement to be made after keeping at room temp.
for 24±2 hrs. (Class I) or 48±4 hrs. (Class II).
NP0: within ±5% or 0.5pF whichever is larger
X7R, X5R: within ±12.5%
Y5V: within ±30%
(This capacitance change means the change of capacitance under
specified flexure of substrate from the capacitance measured before
the test.)
11. Resistance to
Soldering Heat
12. Temperature Cycle
* Solder temperature: 260±5°C
* No remarkable damage.
* Dipping time: 10±1 sec
* Cap change:
* Preheating: 120 to 150°C for 1 minute before imme rse NP0: within ±2.5% or 0.25pF whichever is larger
the capacitor in a eutectic solder.
X7R, X5R: within ±7.5%
* Before initial measurement (Class II only): Perform
150+0/-10°C for 1 hr and then set for 48±4 hrs at r oom
temp.
* Measurement to be made after keeping at room temp.
Y5V: within ±20%
* Q/D.F., I.R. and dielectric strength: To meet initial requirements.
* 25% max. leaching on each edge.
for 24±2 hrs. (Class I) or 48±4 hrs. (Class II).
* Conduct the five cycles according to the temperatures
and time.
Step
Temp. (°C)
Time (min.)
1 Min. operating temp. +0/-3 30±3
2 Room temp.
2~3
3 Max. operating temp. +3/-0 30±3
* No remarkable damage.
* Cap change
NP0: within ±2.5% or 0.25pF whichever is larger
X7R, X5R: within ±7.5%
Y5V: within ±20%
* Q/D.F., I.R. and dielectric strength: To meet initial requirements.
4 Room temp.
2~3
* Before initial measurement (Class II only): Perform
150+0/-10°C for 1 hr and then set for 48±4 hrs at r oom
temp.
* Measurement to be made after keeping at room temp.
for 24±2 hrs. (Class I) or 48±4 hrs. (Class II).
Page 10 of 16
ASC_General Purpose_001M_DS-IBD
Apr. 2011
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]