DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

MC0402B0R5F101CT View Datasheet(PDF) - Unspecified

Part Name
Description
Manufacturer
MC0402B0R5F101CT Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Multilayer Ceramic Capacitor
General Purpose
Reliability Test Conditions and Requirements
No.
Item
4.
Dielectric
Strength
5.
Insulation
Resistance
Test Condition
* To apply voltage (100 V)
250%.
* Duration: 1 to 5 s
* Charge and discharge current
less than 50 mA
To apply rated voltage for
maximum 120 s
With no electrical load
Requirements
* No evidence of damage or flash over during test
10 Gor R × C 500 F whichever is smaller
6.
Temperature
Coefficient
T.C. Operating Temperature
NPO -55°C to 125°C at 5°C
X7R -55°C to 125°C at 25°C
Y5V -25°C to 85°C at 20°C
Adhesive
* Pressurizing force : 5 N (
7.
Strength of
0603) and 10 N (>0603)
Termination
* Test time: 10 ±1 s
T.C.
NPO
X7R
Y5V
Capacitance Change
Within ±30 ppm/°C
Within ±15%
Within +30% / -80%
* No remarkable damage or removal of the terminations
* Vibration frequency: 10 to 55
Hz / minimum
8.
Vibration
Resistance
* Total amplitude: 1.5 mm
* Test time: 6 hours (Two hours
each in three mutually
perpendicular directions)
* No remarkable damage
* Cap change and Q/D.F.: To meet initial specification
9.
Solderability
* Solder temperature: 235 ±5°C
* Dipping time: 2 ±0.5 s
95% minimum coverage of all metalized area
* The middle part of substrate
shall be pressurized by means * No remarkable damage.
of the pressurizing rod at a rate Cap change:
of about 1 mm per second until NPO: within ±5% or ±05 pF whichever is larger X7R, X5R: within
10. Bending Test
the deflection becomes 1 mm
and then the pressure shall be
±12.5%
Y5V: within ±30%
maintained for 5 ±1 s
(This capacitance change means the change of capacitance under
* Measurement to be made after specified flexure of substrate from the capacitance measured
keeping at room temperature for before the test)
24 ±2 hours
* Solder temperature: 270 ±5°C
* Dipping time: 10 ±1 s
* Preheating: 120 to 150°C for 1
minute before immerse the
* No remarkable damage.
capacitor in a eutectic solder
Cap change:
Resistance to * Before initial measurement
NPO: within ±2.5% or ±0.25 pF whichever is larger
11.
Soldering
(Class II only):
X7R: within ±7.5%
Heat
Perform 150 +0 / -10°C for 1
Y5V: within ±20%
hour and then set for 48 ±4
* Q/D.F., I.R. and dielectric strength: To meet initial requirements
hours at room temperature
* 25% maximum leaching on each edge
* Measurement to be made after
keeping at room temperature for
48 ±4 hours
www.element14.com
www.farnell.com
www.newark.com
Page <8>
17/02/12 V1.1
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]