DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

TSA5059 View Datasheet(PDF) - Philips Electronics

Part Name
Description
Manufacturer
TSA5059 Datasheet PDF : 24 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Philips Semiconductors
2.7 GHz I2C-bus controlled low phase
noise frequency synthesizer
Preliminary specification
TSA5059
Four open-collector output ports are provided on the IC for
general purpose; three of these can also be used as input
ports. A 3-bit ADC is also available.
The TSA5059 is controlled via the two-wire I2C-bus.
For programming, there is one 7-bit module address and
the R/W bit for selecting READ or WRITE mode. To be
able to have more than one synthesizer in an I2C-bus
system, one of four possible addresses is selected
depending on the voltage applied at pin AS (see Table 3).
The TSA5059 fulfils the fast mode I2C-bus, according to
the Philips I2C-bus specification. The I2C-bus interface is
designed in such a way that pins SCL and SDA can be
connected either to 5 or to 3.3 V pulled-up I2C-bus lines,
allowing the PLL synthesizer to be connected directly to
the bus lines of a 3.3 V microcontroller.
WRITE mode: R/W = 0
After the address transmission (first byte), data bytes can
be sent to the device (see Table 1). Four data bytes are
needed to fully program the TSA5059. The bus transceiver
has an auto-increment facility that permits programming of
the TSA5059 within one single transmission
(address + 4 data bytes).
The TSA5059 can also be partly programmed on the
condition that the first data byte following the address is
byte 2 or byte 4. The meaning of the bits in the data bytes
is given in Table 1. The first bit of the first data byte
transmitted indicates whether byte 2 (first bit is logic 0) or
byte 4 (first bit is logic 1) will follow. Until an I2C-bus STOP
condition is sent by the controller, additional data bytes
can be entered without the need to re-address the device.
To allow a smooth frequency sweep for fine tuning, and
while the data of the dividing ratio of the main divider is in
data bytes 2, 3 and 4, it is necessary for changing the
frequency to send the data bytes 2 to 5 in a repeated
sending, or to finish an incomplete transmission by a
STOP condition. Repeated sending of data bytes 2 and 3
without ending the transmission does not change the
dividing ratio. To illustrate, the following data sequences
will change the dividing ratio:
Bytes 2, 3, 4 and 5
Bytes 4, 5, 2 and 3
Bytes 2, 3, 4 and STOP
Bytes 4, 5, 2 and STOP
Bytes 2, 3 and STOP
Bytes 2 and STOP
Bytes 4 and STOP.
Table 1 Write data format
BYTE
DESCRIPTION
MSB(1)
LSB CONTROL BIT
1 address
1
1
0
0
0 MA1 MA0 0
A
2 programmable divider 0
N14 N13 N12 N11 N10 N9 N8
A
3 programmable divider N7
N6 N5 N4 N3 N2 N1 N0
A
4 control data
1
N16 N15 PE R3 R2 R1 R0
A
5 control data
C1
C0 XCE XCS P3 P2/T2 P1/T1 P0/T0
A
Note
1. MSB is transmitted first.
1999 Oct 05
6
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]