Integrated circuits, Transistor, Semiconductors Free Datasheet Search and Download Site


M27C256B-10B1 View Datasheet(PDF) - STMicroelectronics

Part NameM27C256B-10B1 ST-Microelectronics
STMicroelectronics ST-Microelectronics
Description256 Kbit (32Kb × 8) UV EPROM and OTP EPROM
M27C256B-10B1 Datasheet PDF : 24 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Device operation
M27C256B
Figure 4.
Programming flowchart
VCC = 6.25V, VPP = 12.75V
n=0
E = 100µs Pulse
NO
++n
= 25
NO
VERIFY
++ Addr
YES
YES
Product(s) FAIL
Last NO
Addr
YES
CHECK ALL BYTES
1st: VCC = 6V
2nd: VCC = 4.2V
AI00760B
olete 2.7
Program inhibit
bs Programming of multiple M27C256Bs in parallel with different data is also easily
O accomplished. Except for E, all like inputs including G of the parallel M27C256B may be
- common. A TTL low level pulse applied to a M27C256B's E input, with VPP at 12.75V, will
) program that M27C256B. A high level E input inhibits the other M27C256Bs from being
t(s programmed.
roduc 2.8
Program Verify
P A verify (read) should be performed on the programmed bits to determine that they were
tecorrectly programmed. The verify is accomplished with G at VIL, E at VIH, VPP at 12.75V and
leVCC at 6.25V.
Obso 2.9
Electronic signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27C256B. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27C256B, with VCC = VPP = 5V. Two identifier bytes may then be sequenced from the
device outputs by toggling address line A0 from VIL to VIH. All other address lines must be
held at VIL during Electronic Signature mode. Byte 0 (A0 = VIL) represents the manufacturer
code and byte 1 (A0 = VIH) the device identifier code. For the STMicroelectronics
M27C256B, these two identifier bytes are given in Table 3 and can be read-out on outputs
Q7 to Q0.
10/24
Direct download click here
HOME 'M27C256B-10B1' Search

Summary description
The M27C256B is a 256 Kbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems and is organized as 32,768 by 8 bits.
The FDIP28W (window ceramic frit-seal package) has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure.
For applications where the content is programmed only one time and erasure is not required, the M27C256B is offered in PDIP28 and PLCC32 packages.
LButtonIn order to meet environmental requirements, ST offers the M27C256B in ECOPACK® packages.
ECOPACK packages are Lead-free. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97.
The maximum ratings related to soldering conditions are also marked on the inner box label.
ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.

Feature summary
■ 5V ± 10% supply voltage in Read operation
■ Access time: 45ns
■ Low power consumption:
   – Active Current 30mA at 5MHz
   – Standby Current 100µA
■ Programming voltage: 12.75V ± 0.25V
■ Programming time: 100µs/Word
■ Electronic signature
   – Manufacturer Code: 20h
   – Device Code: 8Dh
■ ECOPACK® packages available

Share Link : 
한국어     日本語     русский     简体中文     español
@ 2015 - 2018  [ Home  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]