DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

Y505310R000K0L View Datasheet(PDF) - Vishay Semiconductors

Part Name
Description
Manufacturer
Y505310R000K0L
Vishay
Vishay Semiconductors Vishay
Y505310R000K0L Datasheet PDF : 5 Pages
1 2 3 4 5
Accutrim™ 1240 (RJ26 Style)
Vishay Foil Resistors
TABLE 5 - COMPARISON
MIL-PRF-39035/3 CHARACTERISTIC H (6)
MODEL 1240 MAXIMUM
TEST GROUP I
Conditioning
Contact resistance variation - CRV (noise)
Immersion
± 1.0 %
± 3.0 % or 3 Ω (7)
No continuous stream of bubbles
± 0.5 %
3 Ω typical, 10 Ω maximum
No continuous stream of bubbles
TEST GROUP I a
Visual and mechanical
Actual effective electrical travel
End resistance
Dielectric withstanding voltage - DWV
Per MIL-STD-202, methods 301 and 105
Atmospheric pressure
Barometric pressure
Insulation resistance
Shaft torque
Thermal shock
Setting stability
No failures
10 to 25 turns
2 % or 2 Ω (7)
600 VAC, 1 min
250 VAC, 1 min
1000 MΩ
3 oz. in. maximum
± 1.0 %
± 1.0 %
No failures
21 ± 2 turns
2 Ω for values 1 kΩ;
5 Ω for values 2 kΩ;
600 VAC, 1 min
250 VAC, 1 min
> 1000 MΩ
3 oz. in. maximum
± 0.5 %
± 0.5 %
TEST GROUP II
Solderability
Per MIL-STD-202, method 208
Per MIL-STD-202, method 208
TEST GROUP III
Resistance temperature characteristic - TCR
Moisture resistance
Contact resistance variation - CRV (noise)
± 0.005 %/°C (± 50 ppm/°C)
± 1.0 %
3.0 % or 3 Ω (7)
± 0.001 %/°C (± 10 ppm/°C)
± 0.5 %
3 Ω typical, 10 Ω maximum
TEST GROUP IV
Settability
Shock
Setting stability
Vibration
Setting stability
Contact resistance variation - CRV (noise)
Salt spray
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
± 1.0 %
3.0 % or 3 Ω (7)
No corrosion
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
3 Ω typical, 10 Ω maximum
No corrosion
TEST GROUP V
Solder heat
Low-temperature operation
Setting stability
Low-temperature storage
High-temperature exposure
Setting stability
Contact resistance variation - CRV (noise)
Integrity of shaft
± 1.0 %
± 1.0 %
± 2.0 %
± 1.0 %
± 3.0 %
± 2.0 %
3 % or 3 Ω (7)
No loosening or breakage
± 0.1 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
± 0.5 %
3 Ω typical, 10 Ω maximum
No loosening or breakage
TEST GROUP VI
Rotational life (200 cycles)
Contact resistance variation - CRV (noise)
Terminal strength
± 2.0 %
3 % or 3 Ω (7)
2 lbs.
± 2.0 %
3 Ω typical, 10 Ω maximum
2 lbs.
TEST GROUP VII
Life (2000 h) at + 85 °C
Life (10 000 h) at + 85 °C
± 3.0 %
± 5.0 %
± 0.1 % typical, ± 1.0 % maximum
± 0.1 % typical, ± 1.0 % maximum
TEST GROUP VIII
Solvent resistance
No failures
No failures
Notes
(1) Maximum is 1.0 % A.Q.L. standard for all specifications except
TCR. (For TCR information, see notes 2 and 3.)
(2) Maximum TCR applies to the 3 σ (sigma) limit or 99.73 % of a
production lot. (Measured end-to-end with wiper off the element.)
(3) Measurements of TCR through the wiper are influenced more by
setting stability and the percentage of the total resistance in use
(at the wiper) than by fundamental resistance change due to
temperature alone. The parameter shown in table 2 is a 2 s
distribution typifying the behavior of the device when used with
40 % or more of the total resistance in use.
(4) Derated linearly for full power at + 85 °C to zero power at
+ 150 °C. See Figure 2 on previous page.
(5) Independent of resistance value. 3 Ω maximum available on
special request.
(6) All ΔR’s are measured to the tolerance specified + 0.01 Ω.
(7) Whichever is greater.
Special Available Options:
Special marking
Burn-in and screening operations.
VISHAY TRIMMERS ARE INSPECTED
100 % for:
• Immersion
• Resistance tolerance check
• End resistance
• Visual-mechanical
• Dynamic tests for continuity, CRV
By sample for:
• TCR
• DWV
Document Number: 63053
Revision: 23-Mar-10
For any questions, contact: foil@vishaypg.com
www.foilresistors.com
3
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]