Integrated circuits, Transistor, Semiconductors Free Datasheet Search and Download Site


EM636165TS-7I View Datasheet(PDF) - Etron Technology

Part NameEM636165TS-7I Etron
Etron Technology Etron
Description1Mega x 16 Synchronous DRAM (SDRAM)


EM636165TS-7I Datasheet PDF : 73 Pages
First Prev 21 22 23 24 25 26 27 28 29 30 Next Last
EtronTech
1M x 16 SDRAM EM636165-XXI
Figure 5. Self Refresh Entry & Exit Cycle
CL K
CKE
CS#
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19
*Note 2
*Note 1
tIS
*Note 3
*Note 4
tRC(min) *Note 7
tSRX
*Note 5
*Note 6
tPDE
RAS#
*Note 8
CAS#
A11
*Note 8
A0-A9
WE #
DQM
DQ
Hi-Z
Hi-Z
Self Refresh Enter
SelfRefresh Exit
AutoRefresh
Note: To Enter SelfRefresh Mode
1. CS#, RAS# & CAS# with CKE should be low at the same clock cycle.
2. After 1 clock cycle, all the inputs including the system clock can be don't care except for CKE.
3. The device remains in SelfRefresh mode as long as CKE stays "low".
Once the device enters SelfRefresh mode, minimum tRAS is required before exit from SelfRefresh.
To Exit SelfRefresh Mode
1. System clock restart and be stable before returning CKE high.
2. Enable CKE and CKE should be set high for minimum time of tSRX.
3. CS# starts from high.
4. Minimum tRC is required after CKE going high to complete SelfRefresh exit.
5. 2048 cycles of burst AutoRefresh is required before SelfRefresh entry and after SelfRefresh exit if the
system uses burst refresh.
Preliminary
25
Rev. 1.1 Apr. 2005
Direct download click here
HOME 'EM636165TS-7I' Search

Overview
The EM636165 SDRAM is a high-speed CMOS synchronous DRAM containing 16 Mbits. It is internally configured as a dual 512K word x 16 DRAM with a synchronous interface (all signals are registered on the positive edge of the clock signal, CLK). Each of the 512K x 16 bit banks is organized as 2048 rows by 256 columns by 16 bits. Read and write accesses to the SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. Accesses begin with the registration of a BankActivate command which is then followed by a Read or Write command.
The EM636165 provides for programmable Read or Write burst lengths of 1, 2, 4, 8, or full page, with a burst termination option. An auto precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst sequence. The refresh functions, either Auto or Self Refresh are easy to use. By having a programmable mode register, the system can choose the most suitable modes to maximize its performance. These devices are well suited for applications requiring high memory bandwidth and particularly well suited to high performance PC applications

Features
· Fast access time: 5/5.5/6.5/7.5 ns
· Fast clock rate: 166/143/125/100 MHz
· Self refresh mode: standard and low power
· Internal pipelined architecture
· 512K word x 16-bit x 2-bank
· Programmable Mode registers
   - CAS# Latency: 1, 2, or 3
   - Burst Length: 1, 2, 4, 8, or full page
   - Burst Type: interleaved or linear burst
   - Burst stop function
· Individual byte controlled by LDQM and UDQM
· Auto Refresh and Self Refresh
· 4096 refresh cycles/64ms
· CKE power down mode
· Single +3.3V±0.3V power supply
· Interface: LVTTL
· 50-pin 400 mil plastic TSOP II package
· Lead Free Package available

 

Share Link : 

한국어     日本語     русский     简体中文     español
@ 2015 - 2018  [ Home  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]