Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

SD-2967 Ver la hoja de datos (PDF) - NEL Frequency Controls

Número de piezacomponentes DescripciónFabricante
SD-2967 CRYSTAL CLOCK OSCILLATORS NEL
NEL Frequency Controls NEL
SD-2967 Datasheet PDF : 2 Pages
1 2
CRYSTAL CLOCK OSCILLATORS
Data Sheet 0202A
SD-A2960 Series Continued
Differential Positive ECL (DPECL) Fast Edge
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Frequency
Duty Cycle
Logic 0 (2)
Logic 1(2)
Rise & Fall Time
Tpd (4)
Jitter,
RMS(3)
Enable Voltage(5)
Disable Voltage
Frequency Stability (1)
Symbol
Conditions
Min
-----
-----
125.0MHz
-----
@ VCC-1.29V
45/55%
VOL
-----
1.35V
VOH
-----
2.28V
tr,tf 20-80%VO with 50 ohm load to VCC-2V -----
-----
-----
-200 psec
-----
-----
-----
-----
-----
dF/F
with VEE = 0V
with VEE = 0V
Overall conditions including:
0V
3.0V
-100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
Typical
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
General Characteristics
Parameter
Supply Voltage
Supply Current
Output current
Operating temperature
Storage temperature
Power Dissipation
Lead temperature
Load
Start-up time
Symbol
Conditions
Min
VCC
-----
3.15V
ICC
50 ohm termination
0.0 mA
To 2.00V below VCC
IO
Low level Output Current 0.0 mA
TA
------
0°C
TS
-----
-55°C
PD
-----
-----
TL
Soldering, 10 sec.
-----
50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required
tS
-----
-----
Environmental and Mechanical Characteristics
Typical
3.3V
-----
-----
-----
-----
-----
-----
2 ms
Mechanical Shock
Thermal Shock
Vibration
Soldering Condition
Hermetic Seal
Per MIL-STD-202, Method 213, Condition E
Per MIL-STD-833, Method 1011, Condition A
0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
300°C for 10 seconds
Leak rate less than 1 x 10 -8 atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) VOL, VOH, referenced to ground (VEE) with VCC = 3.3V
3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization.
4) Tpd is phse shift between the falling edge of pin 4 at 2.0V and the rising edge of pin 5 at 2.01V.
5) Open to enable pin also enables the output.
Rev. B
Max
312.5MHz
55/45%
1.70V
2.56V
600 psec
+200 psec
3 psec
1.0V
VCC
+100ppm
Max
3.45V
80 mA
±50.0 mA
70°C
125°C
276 mW
300°C
10 ms
Creating a Part Number
SD - A296X - FREQ
Package Code
SD 6 pad 5x7mm SMD
Input Voltage
Code Specification
A
3.3V
B
2.5V
5V
Tolerance/Performance
0 ±100ppm 0-70°C
1 ±50ppm 0-70°C
7 ±25ppm 0-70°C
9 Customer Specific
A ±20ppm 0-70°C
B ±50ppm -40 to +85°C
C ±100ppm -40 to +85°C
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: nelsales@nelfc.com www.nelfc.com
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]