DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

MTV212MV64I View Datasheet(PDF) - Myson Century Inc

Part Name
Description
Manufacturer
MTV212MV64I Datasheet PDF : 26 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
MYSON
TECHNOLOGY
MTV212M64i
(Rev 0.9)
6.1 Composite SYNC separation/insertion
The MTV212M64i continuously monitors the input HSYNC, if the vertical SYNC pulse can be extracted from
the input, a CVpre flag is set and users can select the extracted "CVSYNC" for the source of polarity check,
frequency count, and VBLANK output. The CVSYNC will have 8us delay compared to the original signal.
The MTV212M64i can also insert pulse to HBLANK output during composite active time of VSYNC. The
insert pulse’s width is 1/8 HSYNC period and the insertion frequency can adapt to original HSYNC. The
HBLANK pulse can be disabled or enabled by setting “NoHins” control bit.
6.2 H/V Frequency Counter
MTV212M64i can discriminate HSYNC/VSYNC frequency and save the information in XFRs. The 14 bits
Hcounter counts the time of 64xHSYNC period, then loads the result into the HCNTH/HCNTL latch. The
output value will be [(128000000/H-Freq) - 1], updated once per VSYNC/CVSYNC period when
VSYNC/CVSYNC is present or continuously updated when VSYNC/CVSYNC is non-present. The 12 bits
Vcounter counts the time between two VSYNC pulses, then loads the result into the VCNTH/VCNTL latch.
The output value will be (62500/V-Freq), updated every VSYNC/CVSYNC period. An extra overflow bit
indicates the condition of H/V counter overflow. The VFchg/HFchg interrupt is set when VCNT/HCNT value
changes or overflows. Table 4.2.1 and Table 4.2.2 show the HCNT/VCNT value under the operations of
12MHz.
6.2.1 H-Freq Table
H-Freq(KHZ)
1
31.5
2
37.5
3
43.3
4
46.9
5
53.7
6
60.0
7
68.7
8
75.0
9
80.0
10
85.9
11
93.8
12
106.3
Output Value (14 bits)
12MHz OSC (hex / dec)
0FDEh / 4062
0D54h / 3412
0B8Bh / 2955
0AA8h / 2728
094Fh / 2383
0854h / 2132
0746h / 1862
06AAh / 1706
063Fh / 1599
05D1h / 1489
0554h / 1364
04B3h / 1203
6.2.2 V-Freq Table
V-Freq(Hz)
1
56
2
60
3
70
4
72
5
75
6
85
Output value (12bits)
12MHz OSC (hex / dec)
45Ch / 1116
411h / 1041
37Ch / 892
364h / 868
341h / 833
2DFh / 735
6.3 H/V Present Check
The Hpresent function checks the input HSYNC pulse, Hpre flag is set when HSYNC is over 10KHz or
cleared when HSYNC is under 10Hz. The Vpresent function checks the input VSYNC pulse, the Vpre flag is
set when VSYNC is over 40Hz or cleared when VSYNC is under 10Hz. The HPRchg interrupt is set when
the Hpre value changes. The VPRchg interrupt is set when the Vpre/CVpre value change. However, the
CVpre flag interrupt may be disabled when S/W disables the composite function.
Revision 0.9
- 10 -
2000/11/17
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]