Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

AD1072-48F Просмотр технического описания (PDF) - MicroPower Direct, LLC

Номер в каталогеКомпоненты Описаниепроизводитель
AD1072-48F Very Low Cost, 72W DIN Rail Mount Single Output AC/DC Power Supplies MPD
MicroPower Direct, LLC MPD
AD1072-48F Datasheet PDF : 2 Pages
1 2
Model Selection Guide
Model
Number
AD1072-12F
AD1072-24F
AD1072-48F
Rated
Power
(W)
72
72
72
Input
Voltage (VAC)
Current (A) Voltage
Universal Range 115 VAC 230 VAC (VDC)
100 - 240
1.0
0.5
12
100 - 240
1.0
0.5
24
100 - 240
1.0
0.5
48
Output
Current (A)
Max)
6.0
3.0
1.5
Current (A)
Range
0 ~ 6.0
0 ~ 3.0
0 ~ 1.5
Overvoltage
Protection
(VDC)
15 ~ 17
27 ~ 30
52 ~ 56
Ripple &
Noise
(mV p-p)
100
150
250
Efficiency
(%, Typ)
78
81
82
Notes:
1. Load regulation is specified for a load change
of 20% to 100%.
2. Ripple & noise is measured using equipment
with 20 Mhz of bandwidth with the unit under
test operating at rated load and a 110 VAC
input. Connection to the unit is made with a
0.1 μF / 630V metalized capacitor & a 47 μF
electrolytic capacitor connected in parallel.
3. Transient recovery is measured to within a 1%
error band for a load step change of 50% to
100%.
4. Isolation resistance is given for Input/Output
and Input/FG. For Output/FG., it is 50 MΩ
5. Overload protection is power limiting. The
unit recovers automatically when the fault is
removed.
6. Over voltage protection is a shut down type.
The unit recovers automatically when the fault
is removed.
7. To mount the unit to the DIN rail, tilt the unit
rearwards from the top, fitting the mount over
the top of the rail. Press back on the bottom
front of the unit until it locks in place on the
rail. To remove the unit from the rail, pull the
removal clip at the bottom rear of the unit
downward with a screw driver. With the clip
down, lift up on the unit from the bottom
front until it clears the rail. Before installation
or removal all wiring should be disconnected
and the main power to the system shut off.
8. When wiring the supply, all lines should be
as thick and short as possible. AWG 14 wire is
recommended for the AD1072F series.
9. The units should be mounted so they are
vertically orientated. Air flow (if it is provided)
would optimally flow from the bottom to the
top of the unit.
10. It is recommended that a fuse be used on the
input of a power supply for protection. For
the AD1072F series a 250VAC 2.0A is recom-
mended.
Derating Curve
Mechanical Dimensions
Units with the optional “FT” outputs may be
easily connected for “Fault Tolerant operation.
Contact the factory for details
Connections TB 1
Pin
Function
1
DC Output (+V)
2
DC Output (-V)
3
FT (Optional)
4
FT (Optional)
5
Frame Ground (FG)
6
AC Input - Neutral
7
AC Input - Live
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]