DEHR33D102KA3B View Datasheet(PDF) - Unspecified
Part Name
Description
Manufacturer
DEHR33D102KA3B Datasheet PDF : 74 Pages
| |||
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C85E.pdf
Sep.14,2018
Type RB: X1: AC760V Specifications and Test Methods
Continued from the preceding page.
No.
Item
Specifications
Test Method
Appearance
Capacitance
Change
I.R.
No marked defect
Within ±10%
1000MΩ min.
Soldering
10 Effect
(On-Preheat)
Dielectric
Strength
Per Item 6
11
Vibration
Resistance
Appearance
Capacitance
No marked defect
Within the specified tolerance
D.F.
2.5% max.
Appearance No marked defect
First the capacitor should be
stored at 120+0/-5°C for
60+0/-5s.
Then, as in the figure, the lead
wires should be immersed in
solder of 260+0/-5°C up to 1.5
Heat
Shield
Capacitor
1.5
to 2.0mm
Molten
Solder
to 2.0mm from the root of
terminal for 7.5+0/-1s.
Pre-treatment:
Capacitor should be stored at 125±2°C for 1h, and apply the
AC4000V(r.m.s.) 60s then placed at room condition* for
24±2h before initial measurements. (Do not apply to SL char.)
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1-minute rate of vibration change
from 10 to 55Hz and back to 10Hz.
Apply for a total of 6h, 2h each in 3 mutually
perpendicular directions.
Humidity
12
(Under
Steady
State)
Capacitance
Change
Char.
B
E
SL
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
D.F.
I.R.
Dielectric
Strength
Appearance
Char.
B, E
SL
3000MΩ min.
Specifications
D.F.<=5.0%
D.F.<=2.5%
Per Item 6
No marked defect
Set the capacitor for 500±12h at 40±2°C in 90 to 95%
relative humidity.
Pre-treatment:
Capacitor should be stored at 125±2°C for 1h, and apply the
AC4000V(r.m.s.) 60s then placed at room condition* for
24±2h berore initial measurements. (Do not apply to SL char.)
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
13
Humidity
Loading
Capacitance
Change
Char.
B
E
SL
Char.
D.F.
B, E
SL
I.R.
3000MΩ min.
Capacitance Change
Within ±10%
Within ±15%
Within ± 5%
Specifications
D.F.<=5.0%
D.F.<=2.5%
Apply the AC760V (r.m.s.) for 500±12h at 40±2°C in 90 to 95%
relative humidity.
Pre-treatment:
Capacitor should be stored at 125±2°C for 1h, and apply the
AC4000V(r.m.s.) 60s then placed at room condition* for
24±2h berore initial measurements. (Do not apply to SL char.)
Post-treatment:
Capacitor should be stored for 1 to 2h at room condition*.
Dielectric
Strength
Per Item 6
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 106kPa
Continued on the following page.
36
|
|
Share Link: 