25Q64BV View Datasheet(PDF) - Winbond

Part Name

Description

Manufacturer

25Q64BV

64M-bit Serial Flash Memory with uniform 4KB sectors and Dual/Quad SPI

Winbond 

W25Q64BV

8.1 Package Types

W25Q64BV is offered in an 8-pin plastic 208-mil width SOIC (package code SS) and 8x6-mm WSON

(package code ZE) as shown in figure 1a, and 1b, respectively. The 300-mil 8-pin PDIP is another option

of package selections (Figure 1c). The W25Q64BV is also offered in a 16-pin plastic 300-mil width SOIC

(package code SF) as shown in figure 1d. Package diagrams and dimensions are illustrated at the end of

this datasheet.

8.2 Chip Select (/CS)

The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is

deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When

deselected, the devices power consumption will be at standby levels unless an internal erase, program or

status register cycle is in progress. When /CS is brought low the device will be selected, power

consumption will increase to active levels and instructions can be written to and data read from the

device. After power-up, /CS must transition from high to low before a new instruction will be accepted.

The /CS input must track the VCC supply level at power-up (see “Write Protection” and figure 31). If

needed a pull-up resister on /CS can be used to accomplish this.

8.3 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)

The W25Q64BV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use

the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising

edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read

data or status from the device on the falling edge CLK.

Dual and Quad SPI instruction use the bidirectional IO pins to serially write instructions, addresses or

data to the device on the rising edge of CLK and read data or status from the device on the falling edge of

CLK. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set.

When QE=1 the /WP pin becomes IO2 and /HOLD pin becomes IO3.

8.4 Write Protect (/WP)

The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in

conjunction with the Status Register’s Block Protect (SEC, TB, BP2, BP1 and BP0) bits and Status

Register Protect (SRP) bits, a portion or the entire memory array can be hardware protected. The /WP

pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the /WP pin (Hardware Write

Protect) function is not available since this pin is used for IO2. See figure 1a, 1b, 1c and 1d for the pin

configuration of Quad I/O operation.

8.5 HOLD (/HOLD)

The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low,

while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored

(don’t care). When /HOLD is brought high, device operation can resume. The /HOLD function can be

useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the

QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is

used for IO3. See figure 1a-d for the pin configuration of Quad I/O operation.

8.6 Serial Clock (CLK)

The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI

Operations")

Publication Release Date: July 08, 2010

-9-

Revision E

Share Link: