Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

FDC10-24D05W View Datasheet(PDF) - Power Mate Technology

Part NameDescriptionManufacturer
FDC10-24D05W 10 watts of output power from a 2 x 1 x 0.4 inch package P-DUKE
Power Mate Technology P-DUKE
FDC10-24D05W Datasheet PDF : 2 Pages
1 2
10 WATTS OUTPUT POWER
2:1 AND 4:1 WIDE INPUT VOLTAGE RANGE
INTERNATIONAL SAFETY STANDARD APPROVAL
SIX-SIDED CONTINUOUS SHIELD
HIGH EFFICIENCY UP TO 86%
STANDARD 2” X 1” X 0.4” PACKAGE
FIXED SWITCHING FREQUENCY
UL E193009
TUV R2054609
CB JPTUV-001422
CE MARK
The FDC10 and FDC10-W series offer 10 watts of output power from a 2 x 1 x 0.4 inch
package. FDC10 series have 21 wide input voltage of 9-18, 18-36 and 36-75VDC.
FDC10-W series have 4:1 ultra wide input voltage of 9-36 and 18-75VDC. The FDC10 and
FDC10-W features 1600VDC of isolation, short-circuit and over-voltage protection, as well
as six sided shielding. The safety approval of EN60950 and UL1950. All models are
particularly suited to telecommunications, industrial, mobile telecom and test equipment
applications. According the extended operation temperature range, there are “M1” and “M2”
version for special application.
T E C H N I C A L S P E C I F I C A T I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted.
OUTPUT SPECIFICATIONS
Output power
10 Watts max
Voltage accuracy
Full load and nominal Vin
± 2%
Minimum load (Note 1)
10% of FL
Line regulation
LL to HL at Full Load
± 1%
Load regulation
10% to 100% FL
Single
Dual
± 1%
± 2%
Cross regulation
Asymmetrical load 25% / 100% FL
± 5%
Ripple and noise
20MHz bandwidth
Single
Dual
50mVp-p
75mVp-p
Temperature coefficient
I0.02% / ºC, max
Transient response recovery time 25% load step change
3.3V output
Over voltage protection 5V output
Zener diode clamp
12V output
15V output
Over load protection % of FL at nominal input
500uS
3.9V
6.2V
15V
18V
150% typ
Short circuit protection
Hiccup, automatics recovery
INPUT SPECIFICATIONS
Input voltage range
FDC10 12V nominal input
24V nominal input
48V nominal input
FDC10-W 24V nominal input
48V nominal input
Input filter
Input surge voltage
100mS max
12V input
24V input
48V input
Input reflected ripple (Note 2) Nominal Vin and full load
9 – 18VDC
18 – 36VDC
36 – 75VDC
9 – 36VDC
18 – 75VDC
Pi type
36VDC
50VDC
100VDC
30mAp-p
Start up time Nominal Vin and constant resistor load
20mS typ
Remote ON/OFF (Note 3)
(Positive logic)
DC-DC ON
DC-DC OFF
(Negative logic)
DC-DC ON
DC-DC OFF
Remote off input current Nominal Vin
Open or 3.5V < Vr < 12V
Short or 0V < Vr < 1.2V
Short or 0V < Vr < 1.2V
Open or 3.5V < Vr < 12V
2.5mA
GENERAL SPECIFICATIONS
Efficiency
See table
Isolation voltage
Isolation resistance
Isolation capacitance
1600VDC, min
109ohms, min
300pF, max
Switching frequency
300KHz, typ
Approvals and standard
IEC60950, UL1950, EN60950
Case material
Nickel-coated copper
Base material
Non-conductive black plastic
Potting material
Dimensions
Weight
MTBF (Note 4)
Epoxy (UL94-V0)
2.00 X 1.00 X 0.40 Inch
(50.8 X 25.4 X 10.2 mm)
27g (0.95oz)
1.976 x 106 hrs
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
(Reference derating curve)
Standard
-25ºC ~ +85ºC (with derating)
M1 (Note 5) -40ºC ~ +85ºC (non-derating)
M2 (W series) -40ºC ~ +85ºC (with derating)
Maximum case temperature
+100ºC
Storage temperature range
Thermal impedance (Note 6)
Thermal shock
-55ºC ~ +105ºC
Nature convection
12ºC/watt
Nature convection with heat-sink 10ºC/watt
MIL-STD-810D
Vibration
10~55Hz, 2G, 30minutes along X,Y and Z
Relative humidity
5% to 95% RH
EMC CHARACTERISTICS
Conducted emissions
EN55022
Level A
Radiated emissions
EN55022
Level A
ESD
EN61000-4-2
Perf. Criteria2
Radiated immunity
EN61000-4-3
Perf. Criteria2
Fast transient
EN61000-4-4
Perf. Criteria2
Surge
EN61000-4-5
Perf. Criteria2
Conducted immunity
EN61000-4-6
Perf. Criteria2
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]