TLP701A View Datasheet(PDF) - Toshiba
Part Name
Description
Manufacturer
TLP701A Datasheet PDF : 16 Pages
| |||
TLP701A
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, Ta = 25 )
Characteristics
Symbol Note
Rating
Unit
LED Input forward current
Input forward current derating
Peak transient input forward
current
(Ta ≥ 85 )
IF
∆IF/∆Ta
IFPT
(Note 1)
25
-0.67
1
mA
mA/
A
Peak transient input forward
current derating
(Ta ≥ 85 )
∆IFPT/∆Ta
-25
mA/
Input reverse voltage
Input power dissipation
Input power dissipation
derating
(Ta ≥ 85 )
VR
PD
∆PD/∆Ta
5
V
40
mW
-1.0
mW/
Detector Peak high-level output current
(Ta = -40 to 100 )
IOPH
(Note 2)
-0.6
A
Peak low-level output current
(Ta = -40 to 100 )
IOPL
(Note 2)
+0.6
Output voltage
VO
35
V
Output power dissipation
PO
80
mW
Output power dissipation
derating
(Ta ≥ 85 )
∆PO/∆Ta
-2.0
mW/
Supply voltage
Common Operating temperature
Storage temperature
Lead soldering temperature
Isolation voltage
(10 s)
AC, 60 s,
R.H. ≤ 60 %
VCC
Topr
Tstg
Tsol
BVS
(Note 3)
(Note 4)
35
-40 to 100
-55 to 125
260
5000
V
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ≤ 1 µs, 300 pps
Note 2: Exponential waveform. Pulse width ≤ 2 µs, f ≤ 15 kHz
Note 3: ≥ 2 mm below seating plane.
Note 4: This device is considered as a two-terminal device: Pins 1, 2 and 3 are shorted together, and pins 4, 5 and 6
are shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol Note Min Typ. Max Unit
Input on-state current
Input off-state voltage
Supply voltage
Peak high-level output current
Peak low-level output current
Operating frequency
IF(ON) (Note 1) 6.5
VF(OFF)
0
VCC
(Note 2) 10
IOPH
IOPL
f
(Note 3)
15
mA
0.8
V
30
-0.2
A
+0.2
25
kHz
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Denotes the operating range, not the recommended operating condition.
Note 3: Exponential waveform. IOPH ≥ -0.3 A (≤ 2.0 µs), IOPL ≤ 0.3 A (≤ 2.0 µs), Ta = 100
©2015 Toshiba Corporation
3
2015-12-25
Rev.5.0
|
|
Share Link: 