DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

AD9012TD View Datasheet(PDF) - Analog Devices

Part Name
Description
Manufacturer
AD9012TD
ADI
Analog Devices ADI
AD9012TD Datasheet PDF : 8 Pages
1 2 3 4 5 6 7 8
NOTES
1Measured with analog input = 0 V.
2Measured by FFT analysis where fundamental is –3 dBc.
3Input slew rate derived from rise time (10% to 90%) of full-scale step input.
4Outputs terminated with two equivalent ’LS00 type loads. (See load circuit.)
5Measured from ENCODE into data out for LSB only.
6For full-scale step input, 8-bit accuracy is attained in specified time.
7Recovers to 8-bit accuracy in specified time, after 150% full-scale input overvoltage.
8Output time skew includes high-to-low and low-to-high transitions as well as
bit-to-bit time skew differences.
AD9012
9ENCODE signal rise/fall times should be less than 30 ns for normal operation.
10Measured at 75 MSPS ENCODE rate. Harmonic data based on worst-case harmonics.
11Analog input frequency = 1.23 MHz.
12RMS signal to rms noise, including harmonics with 1.23 MHz. Analog input
signal.
13NPR measured @ 0.5 MHz. Noise source is 250 mW (rms) from 0.5 MHz
to 8 MHz.
14Supplies should remain stable within ± 5% for normal operation.
15Measured at –5.2 V ± 5% and +5.0 V ± 5%.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS1
Positive Supply Voltage (+VS) . . . . . . . . . . . . . . . . . . . . . . 6 V
Analog to Digital Supply Voltage Differential (–VS) . . . 0.5 V
Negative Supply Voltage (–VS) . . . . . . . . . . . . . . . . . . . . –6 V
Analog Input Voltage . . . . . . . . . . . . . . . . . . . . –VS to +0.5 V
ENCODE Input Voltage . . . . . . . . . . . . . . . . . –0.5 V to +5 V
OVERFLOW INH Input Voltage . . . . . . . . . . . –5.2 V to 0 V
Reference Input Voltage (+VREF, –VREF)2 . . –3.5 V to +0.1 V
Differential Reference Voltage . . . . . . . . . . . . . . . . . . . . 2.1 V
Reference Midpoint Current . . . . . . . . . . . . . . . . . . . . ± 4 mA
Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 30 mA
Operating Temperature Range
AD9012AQ/BQ/AJ/BJ . . . . . . . . . . . . . . . –25°C to +85°C
AD9012SE/SQ/TE/TQ . . . . . . . . . . . . . . –55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature3 . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead Soldering Temperature (10 sec) . . . . . . . . . . . . . 300°C
NOTES
1Absolute Maximum Ratings are limiting values, to be applied individually, and
beyond which the serviceability of the circuit may be impaired. Functional
operability under any of these conditions is not necessarily implied. Exposure to
absolute maximum rating conditions for extended periods may affect device
reliability.
2+VREF –VREF under all circumstances.
3Maximum junction temperature (TJ max) should not exceed 150°C for ceramic
and plastic packages:
TJ = PD (θJA) + TA
PD (θJC) + Tc
where:
PD = power dissipation
θJA = thermal impedance from junction to ambient (°C/W)
θJC = thermal impedance from junction to case (°C/W)
TA = ambient temperature (°C)
TC = case temperature (°C)
Typical thermal impedances are:
Ceramic DIP θJA = 42°C/W; θJC = 10°C/W
Ceramic LCC θJA = 50°C/W; θJC = 15°C/W
JLCC θJA = 59°C/W; θJC = 15°C/W
Recommended Operating Conditions
Parameter
–VS
+VS
+VREF
–VREF
Analog Input
Min
–5.46
+4.75
–VREF
–2.1
–VREF
Input Voltage (V)
Nominal
Max
–5.20
+5.00
0.0
–2.0
–4.94
+5.25
+0.1
+VREF
+VREF
TTL
OUTPUT
15pF
VS
1k
Figure 1. Load Circuit
EXPLANATION OF TEST LEVELS
Test Level
I – 100% production tested.
II – 100% production tested at 25°C, and sample tested at
specified temperatures. AC testing done on sample basis.
III – Sample tested only.
IV – Parameter is guaranteed by design and characterization
testing.
V – Parameter is a typical value only.
VI – All devices are 100% production tested at 25°C. 100%
production tested at temperature extremes for extended
temperature devices; guaranteed by design and
characterization testing for industrial devices.
ORDERING GUIDE
Device
Linearity
Temperature
Ranges
Package
Options*
AD9012AQ
AD9012BQ
AD9012AJ
AD9012BJ
AD9012SQ
AD9012SE
AD9012TQ
AD9012TE
0.75 LSB
0.50 LSB
0.75 LSB
0.50 LSB
0.75 LSB
0.75 LSB
0.50 LSB
0.50 LSB
–25°C to +85°C
–25°C to +85°C
–25°C to +85°C
–25°C to +85°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
–55°C to +125°C
Q-28
Q-28
J-28A
J-28A
Q-28
E-28A
Q-28
E-28A
*E = Leadless Ceramic Chip Carrier; J = Ceramic Leaded Chip Carrier;
Q = Cerdip.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD9012 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
REV. F
–3–
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]