Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits
Part Name  

5962-0323701MXA View Datasheet(PDF) - International Rectifier

Part Name5962-0323701MXA IR
International Rectifier IR
DescriptionUltra Low Dropout, 7.0 A Adjustable Positive Linear Regulator Surface-Mount (SMD-6)
5962-0323701MXA Datasheet PDF : 4 Pages
1 2 3 4
OM7580SM
Electrical Characteristics @TA = 25°C (Unless Otherwise Specified)
Parameter
Test Conditions
Min. Typ. Max. Units
Reference Voltage VCTRL = 2.7V, VPWR = 2.0V, ILOAD = 10mA
1.243
VADJ= 0V
VCTRL=2.7 to 12V, VPWR=1.75V to 5.5V, ILOAD =10mA to 6.0A Q 1.237
Line Regulation
VCTRL = 2.5 to 12V, VPWR = 3.0V to 5.5V, ILOAD = 1.0mA Q
--
Load Regulation
VCTRL = 2.75V, VPWR = 2.1V, ILOAD = 10mA to 6.0A Q
--
Minimum Load Current VCTRL = 5.0V, VPWR = 3.3V, VADJ= 0V QR
--
Ground Pin Current VCTRL = 5.0V, VPWR = 3.3V, ILOAD = 0mA Q
--
VCTRL= 2.75V, VPWR= 2.05V, ILOAD= 7.0A, TJ = 25°C
--
Control Pin Current SVCTRL= 2.75V, VPWR= 2.05V, ILOAD= 7.0A, TJ = 125°C
--
VCTRL= 2.75V, VPWR= 2.05V, ILOAD= 6.0A, TJ = -55°C
--
Adjust Pin Current
VCTRL= 2.75V, VPWR = 2.05V, ILOAD = 10mA
--
VADJ= 0V
Ripple Rejection
VCTRL = VPWR = 5.0V (AVG), VRIPPLE = 1.0VP-P, f= 120Hz
60
IOUT = 4.0A TJ = 25°C
Current Limit
VCTRL= 2.75V, VPWR= 2.05V, VOUT = 100mV, TJ = 25°C
7.1
VCTRL=2.75V, VPWR=2.05V, VOUT=100mV, TJ=-55°C & TJ=+125°C 6.6
VPWR = 3.3V, ILOAD = 7.0A, TJ = 25°C
--
Minimum VCONTROL VPWR = 3.3V, ILOAD = 7.0A, TJ = 125°C
--
VPWR = 3.3V, ILOAD = 6.0A, TJ = -55°C
--
VCTRL = 2.75V, ILOAD = 7.0A, TJ = 25°C
--
Minimum VPWR
VCTRL = 2.75V, ILOAD = 7.0A, TJ = 125°C
--
VCTRL = 2.75V, ILOAD = 6.0A, TJ = -55°C
--
Thermal Regulation VPWR = 5.0V, IO = 7.0A, PD 20W, pulse width = 30ms
--
1.250
1.250
1.0
1.0
5.0
6.0
--
--
--
50
80
8.0
--
--
--
--
--
--
--
--
1.257
1.263
3.0
5.0
10
10
120
120
130
120
--
--
--
1.33
1.33
1.35
0.62
0.80
0.80
0.02
V
mV
mA
µA
dB
A
V
V
%/W
Dropout is caused by either minimum control voltage or minimum power voltage. Both
Dropout Voltage
parameters are specified with respect to the output voltage. The specifications represent the
minimum input/output voltage required to maintain 1% regulation.
Footnotes
Q- Denotes specifications which apply over the full operating temperature range.
R- The minimum load current is minimum current required to maintain regulation. Normally the current in
the resistor divider used to set the output voltage is selected to meet the minimum load current
requirement.
S- The control pin current is the drive current required for the output transistor. The control pin current is
approximately 0.01% output current. The minimum value is equal to quiescent current of the device.
2
www.irf.com
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]