DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

ADF4360-2BCPRL View Datasheet(PDF) - Analog Devices

Part Name
Description
Manufacturer
ADF4360-2BCPRL
ADI
Analog Devices ADI
ADF4360-2BCPRL Datasheet PDF : 24 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ADF4360-2
Parameter
RF OUTPUT CHARACTERISTICS5
VCO Output Frequency
VCO Sensitivity
Lock Time6
Frequency Pushing (Open Loop)
Frequency Pulling (Open Loop)
Harmonic Content (Second)
Harmonic Content (Third)
Output Power5, 7
Output Power Variation
VCO Tuning Range
NOISE CHARACTERISTICS5
VCO Phase-Noise Performance8
Synthesizer Phase-Noise Floor9
In-Band Phase Noise10, 11
RMS Integrated Phase Error12
Spurious Signals due to PFD Frequency11, 13
Level of Unlocked Signal with MTLD Enabled
B Version Unit
Conditions/Comments
1850/2170 MHz min/max
57
400
6
15
−19
−37
−13/−6
±3
1.25/2.7
MHz/V typ
μs typ
MHz/V typ
kHz typ
dBc typ
dBc typ
dBm typ
dB typ
V min/max
ICORE = 20 mA, RF < 2 GHz
ICORE = 15 mA, RF > 2 GHz
To within 10 Hz of final frequency
Into 2.00 VSWR load
Programmable in 3 dB steps (see Table 7)
For tuned loads, see the Output Matching section
−110
−133
−141
−147
−172
−163
−147
−83
0.64
−70
−42
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
Degrees typ
dBc typ
dBm typ
@ 100 kHz offset from carrier
@ 1 MHz offset from carrier
@ 3 MHz offset from carrier
@ 10 MHz offset from carrier
@ 25 kHz PFD frequency
@ 200 kHz PFD frequency
@ 8 MHz PFD frequency
@ 1 kHz offset from carrier
100 Hz to 100 kHz
1 Operating temperature range is −40°C to +85°C.
2 Guaranteed by design. Sample tested to ensure compliance.
3 ICP is internally modified to maintain constant loop gain over the frequency range.
4 TA = 25°C; AVDD = DVDD = VVCO = 3.3 V; P = 32.
5 For RF > 2 GHz, these characteristics are guaranteed only for VCO core power = 15 mA. For frequencies < 2 GHz, these characteristics are guaranteed only for VCO core
power = 20 mA.
6 Jumping from 2.0 GHz to 2.17 GHz. PFD frequency = 200 kHz; loop bandwidth = 10 kHz.
7 Using 50 Ω resistors to VVCO into a 50 Ω load. For tuned loads, see the Output Matching section.
8 The noise of the VCO is measured in open-loop conditions.
9 The synthesizer phase-noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 log N (where N is the N divider value).
10 The phase noise is measured with the EVAL-ADF4360-xEB1 Evaluation Board and the HP8562E spectrum analyzer. The spectrum analyzer provides the REFIN for the
synthesizer; offset frequency = 1 kHz.
11 fREFIN = 10 MHz; fPFD = 200 kHz; N = 10000; Loop B/W = 10 kHz.
12 fREFIN = 10 MHz; fPFD = 1 MHz; N = 2000; Loop B/W = 25 kHz.
13 The spurious signals are measured with the EVAL-ADF4360-xEB1 Evaluation Board and the HP8562E spectrum analyzer. The spectrum analyzer provides the REFIN for
the synthesizer; fREFOUT = 10 MHz @ 0 dBm.
Rev. B | Page 4 of 24
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]