DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

TS3011 View Datasheet(PDF) - STMicroelectronics

Part Name
Description
Manufacturer
TS3011
ST-Microelectronics
STMicroelectronics ST-Microelectronics
TS3011 Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Electrical characteristics
TS3011
Table 4. VCC = +2.7 V, VICM = VCC/2, Tamb = +25°C (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
VIO Input offset voltage(2)
ΔVIO Input offset voltage drift
VHYST Input hysteresis voltage(3)
IIO Input offset current(4)
-40°C < Tamb < +125°C
-40°C < Tamb < +125°C
-40°C < Tamb < +125°C
IIB Input bias current
ICC Supply current
ISC Short circuit current
-40°C < Tamb < +125°C
No load, output high
-40°C < Tamb < +125°C
No load, output low
-40°C < Tamb < +125°C
Source
Sink
VOH Output voltage high
VOL Output voltage low
CMRR Common mode rejection ratio
TPLH
Propagation delay(5)
low to high output level
Isource = 4 mA
-40°C < Tamb < +125°C
Isink = 4 mA
-40°C < Tamb < +125°C
0 < VICM < 2.7 V
CL = 12 pF, RL = 1 MΩ
Overdrive = 5 mV
Overdrive = 15 mV
Overdrive = 50 mV
TPHL
Propagation delay(6)
high to low output level
CL = 12 pF, RL = 1 MΩ
Overdrive = 5 mV
Overdrive = 15 mV
Overdrive = 50 mV
TR Rise time (10% to 90%)
CL = 12 pF, RL = 1 MΩ
Overdrive = 100 mV
TF Fall time (90% to 10%)
CL = 12 pF, RL = 1 MΩ
Overdrive = 100 mV
-7
-0.1
-9
5
2
1
1
0.52
0.66
24
27
19
22
2.48 2.52
2.40
130
52
70
7
9
mV
20 μV/°C
mV
20
100
pA
20
100
pA
0.65
0.9
mA
0.89
1.1
mA
V
170
220
mV
dB
16
11
ns
9
13
16
11
ns
9
13
2.3
ns
1.8
ns
1. All values over the temperature range are guaranteed through correlation and simulation. No production tests are
performed at the temperature range limits.
2. The offset is defined as the average value of positive (VTRIP+) and negative (VTRIP-) trip points (input voltage differences
requested to change the output state in each direction.
3. Hysteresis is a built-in feature of the TS3011. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
5. Overdrive is measured with reference to the VTRIP+ point.
6. Overdrive is measured with reference to the VTRIP- point.
4/14
Doc ID 022078 Rev 1
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]