ADV611JST View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADV611JST

Closed Circuit TV Digital Video Codec

Analog Devices 

ADV611/ADV612

[7] Video Interface Encode/Decode Mode Select, E/D. This bit selects the following:

0 Decode mode video interface (compressed-to-raw)

1 Encode mode video interface (raw-to-compressed), reset value

[8] Reserved (always write zero)

[9] Video Interface Bipolar/Unipolar Color Component Select, BUC. This bit selects the following:

0 Bipolar color component mode video interface, reset value

1 Unipolar color component mode video interface

[10] Reserved (always write zero)

[11] Video Interface Software Reset, SWR. This bit has the following effects on ADV611/ADV612 operations:

0 Normal operation

1 Software Reset. This bit is set on hardware reset and must be cleared before the ADV611/ADV612 can begin processing.

(reset value)

When this bit is set during encode, the ADV611/ADV612 completes processing the current field then suspends operation

until the SWR bit is cleared. When this bit is set during decode, the ADV611/ADV612 suspends operation immediately and

does not resume operation until the SWR bit is cleared. Note that this bit must be set whenever any other bit in the Mode

register is changed.

[12] HSYNC pin Polarity, PHSYNC. This bit has the following effects on ADV611/ADV612 operations:

0 HSYNC is HI during blanking, reset value

1 HSYNC is LO during blanking (HI during active)

[13] HIRQ pin Polarity, PHIRQ. This bit has the following effects on ADV611/ADV612 operations:

0 HIRQ is active LO, reset value

1 HIRQ is active HI

[14] Quality Box Enable, QBE. This bit has the following effect on ADV611/ADV612 operations:

0 Video area registers (HSTART, HEND, VSTART, VEND). Crop video area, setting cropped area to all 0

quantizations (ADV601 mode), reset value

1 Video area registers (HSTART, HEND, VSTART, VEND). Select Quality Box. Quantization of the area outside

the box is selected with the background Contrast Control register. See the video area registers for more information

on the Quality Box.

[15] Video Stall Enable, VSE. This bit has the following effect on ADV611/ADV612 operations:

0 Video Stall disabled (ADV601 mode), reset value

1 Video Stall enabled.

FIFO Control Register

Indirect (Read/Write) Register Index 0x01

This register holds the service-request settings for the ADV611/ADV612’s host interface FIFO, causing interrupts for the “nearly full” and

“nearly empty” levels. Because each register is four bits in size, and the FIFO is 512 positions, the 4-bit value must be multiplied by 32

(decimal) to determine the exact value for encode service level (nearly full) and decode service level (nearly empty). The ADV611/ADV612

uses these settings to determine when to generate a FIFO Service Request related host interrupt (FIFOSRQ bit and FIFO_SRQ pin).

[3:0]

Encode Service Level, ESL[3:0]. The value in this field determines when the FIFO is considered nearly full on encode; a condi-

tion that generates a FIFO service request condition in encode mode. Since this register is four bits (16 states), and the FIFO is

512 positions, the step size for each bit in this register is 32 positions. The following table summarizes sample states of the

register and their meaning.

ESL Interrupt When . . .

0000 Disables service requests (FIFO_SRQ never goes HI during encode)

0001 FIFO has only 32 positions filled (FIFO_SRQ when >= 32 positions are filled)

1000 FIFO is 1/2 full, reset value

1111 FIFO has only 32 positions empty (480 positions filled)

[7:4]

Decode Service Level, DSL[7:4]. The value in this field determines when the FIFO is considered nearly empty in decode; a

condition that generates a FIFO service request in decode mode. Because this register is four bits (16 states), and the FIFO

is 512 positions, the step size for each bit in this register is 32 positions. The following table summarizes sample states of the

register and their meaning.

DSL Interrupt When . . .

0000 Disables service requests (FIFO_SRQ never goes HI)

0001 FIFO has only 32 positions filled (480 positions empty)

1000 FIFO is 1/2 empty, reset value

1111 FIFO has only 32 positions empty (FIFO_SRQ when >= 32 positions are empty)

[15:8] Reserved (always write zero)

REV. 0

–13–

Share Link: