TC1263-3.0VETTR View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
TC1263-3.0VETTR Datasheet PDF : 18 Pages
| |||
TC1263
1.0 ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage .........................................................6.5V
Output Voltage................ (GND – 0.3V) to (VIN + 0.3V)
Power Dissipation................Internally Limited (Note 7)
Voltage (max.) on Any Pin: (GND – 0.3V) to (VIN + 0.3V)
Operating Temperature Range.... -40°C < TJ < +125°C
Storage Temperature..........................-65°C to +150°C
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, VIN = VR + 1.0V, (Note 1), IL = 100 µA, CL = 3.3 µF,
SHDN > VIH, TA = +25°C. Boldface type specifications apply for junction temperatures of -40°C to +125°C.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Input Operating Voltage
Maximum Output Current
Output Voltage
VOUT Temperature Coefficient
Line Regulation
Load Regulation (Note 4)
Dropout Voltage (Note 5)
Supply Current
Shutdown Supply Current
Power Supply Rejection Ratio
VIN
IOUTMAX
VOUT
VOUT/T
VOUT/VIN
VOUT/VOUT
VIN-VOUT
IDD
ISHDN
PSRR
2.7
—
6.0
V Note 2
500
—
—
mA
VR – 2.5% VR ± 0.5% VR + 2.5% V Note 1
—
40
—
ppm/°C Note 3
—
–0.01
—
—
—
—
—
—
0.05
0.002
20
60
200
350
80
0.05
0.35
+0.01
30
130
390
650
130
1
%
%/mA
mV
µA
µA
(VR + 1V) VIN6V
IL = 0.1 mA to IOUTMAX
IL = 100 µA
IL = 100 mA
IL = 300 mA
IL = 500 mA
SHDN = VIH, IL = 0
SHDN = 0V
—
64
—
db F 1 kHz
Output Short Circuit Current
IOUTSC
—
1200
1400
mA VOUT = 0V
Thermal Regulation
VOUT/PD
—
0.04
—
V/W Note 6
Output Noise
eN
—
260
—
nV/Hz IL = IOUTMAX, F = 10 kHZ
Note 1:
2:
3:
4:
5:
6:
7:
VR is the regulator output voltage setting.
The minimum VIN has to justify the conditions: VIN VR + VDROPOUT and VIN 2.7V for IL = 0.1 mA to IOUTMAX.
TCVOUT = ---V----O----U---T---M----A---V-X---O-–--U---V-T---O---U----T---TM----I--N-------–-----1---0---6-
Regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal
value measured at a 1.0V differential.
Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 ms.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, JA). Exceeding the maximum allowable power
dissipation causes the device to initiate thermal shutdown. Please see Section 5.0 “Thermal Considerations” for
more details.
DS21374D-page 2
2002-2012 Microchip Technology Inc.
|
|
Share Link: 