Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

28233-11 View Datasheet(PDF) - Conexant Systems

Part NameDescriptionManufacturer
28233-11 ATM Transmitter/Receiver with UTOPIA Interface Conexant
Conexant Systems Conexant
28233-11 Datasheet PDF : 161 Pages
First Prev 41 42 43 44 45 46 47 48 49 50 Next Last
ATM Transmitter/Receiver with UTOPIA Interface
2.0 Functional Description
2.3 Overhead Generation
2.3.4 STS-1 and STS-3c/STM-1 Modes
All framing overhead is generated automatically and all BIP overhead is
calculated and inserted in the proper positions. BIP fields can be errored using the
TXFEAC_ERRPAT register [0x03] and BIP Error Insert [bits 1210] of
CONFIG_2 [0x01]. Groups of overhead octets can be disabled (set to all 0s) using
Overhead Control [bits 30] of CONFIG_2. Internally generated octets are A1,
A2, C1, B1, B3, C2, H1, H2, H3, G1, B2, K2, H4, and M1.
In STS-1 mode, if STS-1 Stuffing Option [bit 15] in CONFIG_1 [0x00] is set,
then columns 30 and 59 in the payload envelope are stuffed with all 0s and are not
available for ATM cell octet transport (resulting in a total of 84 columns available
for transport). If this bit is not set, then all 86 columns of the SPE are available for
ATM cell octets.
The C1 octet can be programmed to be obtained from the TXOVH bus by
setting Enable External Section Trace [bit 1] of CONFIG_4 [0x29]. The C1
values generated are listed in order of precedence in Table 2-11.
Table 2-11. C1 Values
Disable C1
Enable External
STS-1 Mode
STS-3c/STM-1 Mode
Control Bit
C1 Octet Value
From TXOVH Bus
The pointer value generated in SONET/SDH modes is controlled by
STM-1/STS-3c Pointer [bit 0] in the CONFIG_4 register [0x29]. This bit should
be set low for STS-1 operation. When this bit is low, the H1/H2 pointer value is
fixed at 0x620A. When this bit is set high (for STM-1 operation), the AU-4
pointer value is fixed at 0x6A0A (SS bits = 10). Overhead generation of STS-1,
STS-3c, and STM-1 values is summarized in Table 2-12.
Table 2-12. STS-1, STS-3c, and STM-1 Overhead Values (1 of 2)
Overhead Byte
CN8223 Operation
A1, A2
H1, H2, H3
Inserts standard values (0xF6, 0x28) or may be inserted externally through port TXOVH[7:0]. If this
bit is disabled, the value is 0x00.
Internally generated (0x00 if disabled; 0x01 in STS-1 mode; 0x01, 0x02, and 0x03 in STS-3c mode).
Can be externally inserted through port TXOVH[7:0].
Calculates and inserts B1. Errors can be inserted using the TXFEAC_ERRPAT register. Allows single
error insertion or all-zero value (continuous error).
Always inserted through port TXOVH[7:0].
Always inserted through port TXOVH[7:0].
Inserted externally through port TXOVH[7:0] or from internal HDLC formatter, if enabled.
Internally generated. The H1 values are 0x62 in STS-3c mode and 0x6A in STM-1 mode. The H2
value is 0x0A in both STS-3c and STM-1 modes. The H3 value is 0x00. If overhead insertion is
disabled, all values are 0x00.
Direct download click here


Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2020  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]