28222-14 View Datasheet(PDF) - Conexant Systems

Part Name

Description

Manufacturer

28222-14

ATM Transmitter/Receiver with UTOPIA Interface

Conexant Systems 

CN8223

ATM Transmitter/Receiver with UTOPIA Interface

2.0 Functional Description

2.2 Line Framers

2.2.2.1 High-Speed

PECL Receive Interface

STS-3c, STM-1 and E4 use the high-speed PECL interface. This mode is used in

any case where an external LIU/decoder is used (such as E4 and STS-3c/STM-1

CMI decoding). If the mode is set to E4 or STS-3c/STM-1 in CONFIG_1, then

the inputs are taken from the “HS±” versions of the input pins. RXDATI input is

sampled on the falling edge of RXCKI. RXDATI can be sampled on the rising

edge of the input clock by setting the Invert RX Clock Sampling bit. Table 2-5

lists the connections for internal framer Rx with the encoder disabled; Figure 2-6

illustrates the timing with the coder disabled.

Table 2-5. Connections for Internal Framer Rx, Encoder Disabled (STS-3c, STM-1, E4)

Signal Name

Connect to CN8223 Pin

Receive Clock Input (RXCKI)

Receive Data (RXDATI)

Receive Loss of Signal (RXLOS~)

RXCKI or RXCKI_HS±

RXIN[0] or RXIN_HS±

RXIN[4]

Figure 2-6. Timing for Internal Framer Receiver, Encoder Disabled

RXCKI

RXDATI

2.2.2.2 Receiver

Framing Operation

Five modes are provided for receiver framing operation: DS3, G.751 E3, G.832

E3/E4, STS-1, and STS-3c/STM-1.

In DS3 mode, a parallel-search framing circuit recovers the subframe and

M-frame alignments in the DS3 signal. Framing is initiated by an out-of-frame

condition as determined by the receiver frame bit-check circuitry. When 3 out of

16 consecutive subframing (F) bits are in error or when 2 out of 3 consecutive

M-frames have M bit errors, an out-of-frame condition is declared.

In G.751 E3 mode, a serial search for the 10-bit FAS pattern (1111 0100 00) is

conducted. When three consecutive correct patterns are found, the receiver is

declared to be in frame. An out-of-frame condition is declared when four

consecutive incorrect FAS patterns are detected.

In G.804 E3/E4 and STS-1/STS-3c/STM-1 modes, an octet alignment by the

serial-to-parallel conversion circuit is found in conjunction with an octet search

for the SONET A1/A2 framing pattern (which is the same pattern as, but not

related to, the PLCP A1/A2 bytes). When two consecutive good patterns are

found, the receiver is declared to be in frame. An out-of-frame (OOF) condition is

declared when four consecutive incorrect A1/A2 patterns are detected.

In STS-3c/STM-1 mode, an octet alignment by the serial-to-parallel

conversion circuit is found in conjunction with an octet search for the third A1

and the first A2 octets.

In STS-1 Mode, if STS-1 Stuffing Option [bit 15] in CONFIG_1 [0x00] is set,

then columns 30 and 59 in the payload envelope are stuff columns, and these

octets will not be interpreted as ATM cell octets. If this bit is not set, then all 86

columns of the SPE will be interpreted as ATM cell octets.

100046C

Conexant

2-7

Share Link: