
Part Name  OR2T06A3M160I  Unspecified 
Description  ORCAÂ® Series 2 FieldProgrammable Gate Arrays 
OR2T06A3M160I Datasheet PDF : 192 Pages

ORCA Series 2 FPGAs
Data Sheet
June 1999
Programmable Logic Cells (continued)
C0
A4
A4
A3
A3 QLUT3
A2
A2
F3
A1
A1 QLUT2
A0
A0
F1
B4
B4
B3
B3 QLUT1
B2
B2
F0
B1
B1 QLUT0
B0
B0
two operands are input into A[3:0] and B[3:0]. The four
result bits, one per QLUT, are F[3:0] (see Figure 9).
The ripple output from QLUT3 can be routed to dedi
cated carryout circuitry into any of four adjacent PLCs,
or it can be placed on the O4 PFU output, or both. This
allows the PLCs to be cascaded in the ripple mode so
that nibblewide ripple functions can be expanded eas
ily to any length.
COUT
B3
A3
B3 COUT
A3 QLUT3
F3
B2
B2
F2
A2
A2 QLUT2
52751(F).r3
Figure 8. F5M Modeâ€”One SixInput Variable
Function
F5M Modeâ€”One SixInput Variable Function
The LUT can be used to implement any function of six
input variables. As shown in Figure 8, five input signals
(A[4:0]) are routed into both the A[4:0] and B[4:0] ports,
and the C0 port is used for the sixth input. The output
port is F1.
Ripple Mode
The LUT can do nibblewide ripple functions with high
speed carry logic. Each QLUT has a dedicated carry
out net to route the carry to/from the adjacent QLUT.
Using the internal carry circuits, fast arithmetic and
counter functions can be implemented in one PFU.
Similarly, each PFU has carryin (CIN) and carryout
(COUT) ports for fastcarry routing between adjacent
PFUs.
The ripple mode is generally used in operations on two
4bit buses. Each QLUT has two operands and a ripple
(generally carry) input, and provides a result and ripple
(generally carry) output. A single bit is rippled from the
previous QLUT and is used as input into the current
QLUT. For QLUT0, the ripple input is from the PFU CIN
port. The CIN data can come from either the fastcarry
routing or the PFU input B4, or it can be tied to logic 1
or logic 0.
The resulting output and ripple output are calculated by
using generate/propagate circuitry. In ripple mode, the
B1
B1
F1
A1
A1 QLUT1
B0
B0 QLUT0
F0
A0
A0
CIN
CIN
Figure 9. Ripple Mode
52756(F).r32
The ripple mode can be used in one of four submodes.
The first of these is adder/subtractor mode. In this
mode, each QLUT generates two separate outputs.
One of the two outputs selects whether the carryin is
to be propagated to the carryout of the current QLUT
or if the carryout needs to be generated. The result of
this selection is placed on the carryout signal, which is
connected to the next QLUT or the COUT signal, if it is
the last QLUT (QLUT3).
The other QLUT output creates the result bit for each
QLUT that is connected to F[3:0]. If an adder/subtractor
is needed, the control signal to select addition or sub
traction is input on A4. The result bit is created in one
half of the QLUT from a single bit from each input bus,
along with the ripple input bit. These inputs are also
used to create the programmable propagate.
10
Lucent Technologies Inc.

Direct download click here 

Share Link : 
All Rights ReservedÂ© datasheetq.com 2015  2019 ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ] 