NB6L295MMNTXG View Datasheet(PDF) - ON Semiconductor
Part Name
Description
Manufacturer
NB6L295MMNTXG
ON Semiconductor
NB6L295MMNTXG Datasheet PDF : 13 Pages
| |||
NB6L295M
Table 4. DC CHARACTERISTICS, MULTI−LEVEL INPUTS VCC = VCC0 = VCC1 = 2.375 V to 3.6 V, GND = 0 V, TA = −40°C to
+85°C
Symbol
Characteristic
Min
Typ
Max
Unit
POWER SUPPLY CURRENT
ICC
Power Supply Current (Inputs, VTX and Outputs Open) (Sum of ICC,
ICC0, and ICC1)
CML OUTPUTS (Notes 5 and 6, Figure 22)
170
215
mA
VOH
Output HIGH Voltage
VCC − 40 VCC − 10
VCC
mV
VCC = VCC0 = VCC1 = 3.3 V
3260
3290
3300
VCC = VCC0 = VCC1 = 2.5 V
2460
2490
2500
VOL
Output LOW Voltage
VCC − 500 VCC − 400 VCC − 300
mV
VCC = VCC0 = VCC1 = 3.3 V
2800
2900
3000
VCC = VCC0 = VCC1 = 2.5 V
2000
2100
2200
DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (see Figures 11 and 12) (Note 7)
Vth
Input Threshold Reference Voltage Range
1050
VIH
Single−Ended Input HIGH Voltage
Vth +150
VIL
Single−Ended Input LOW Voltage
GND
VISE
Single−Ended Input Voltage Amplitude (VIH − VIL)
300
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (see Figures 13 and 14) (Note 8)
VCC − 150
mV
VCC
mV
Vth − 150
mV
VCC − GND
mV
VIHD
Differential Input HIGH Voltage
VILD
Differential Input LOW Voltage
VID
Differential Input Voltage Swing (INx, INx) (VIHD − VILD)
VCMR Input Common Mode Range (Differential Configuration) (Note 9)
IIH
Input HIGH Current INx/INX, (VTn/VTn Open)
IIL
Input LOW Current IN/INX, (VTn/VTn Open)
SINGLE−ENDED LVCMOS/LVTTL CONTROL INPUTS
1200
GND
150
950
−150
−150
VCC
mV
VCC − 150
mV
VCC − GND
mV
VCC – 75
mV
150
mA
150
mA
VIH
Single−Ended Input HIGH Voltage
VIL
Single−Ended Input LOW Voltage
IIH
Input HIGH Current
IIL
Input LOW Current
TERMINATION RESISTORS
2000
GND
−150
−150
VCC
mV
800
mV
150
mA
150
mA
RTIN
RTOUT
Internal Input Termination Resistor
Internal Output Termination Resistor
40
50
40
50
60
W
60
W
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. CML outputs loaded with 50 W to VCC for proper operation.
6. Input and output parameters vary 1:1 with VCC.
7. Vth, VIH, VIL, and VISE parameters must be complied with simultaneously. Vth is applied to the complementary input when operating in
single−ended mode.
8. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously.
9. VCMR(min) varies 1:1 with voltage on GND pin, VCMR(max) varies 1:1 with VCC. The VCMR range is referenced to the most positive side of
the differential input signal.
http://onsemi.com
5
|
|
Share Link: