Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

MC-4516DA726P 查看數據表(PDF) - Elpida Memory, Inc

零件编号产品描述 (功能)生产厂家
MC-4516DA726P 16 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE REGISTERED TYPE Elpida
Elpida Memory, Inc Elpida
MC-4516DA726P Datasheet PDF : 16 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
MC-4516DA726
DC Characteristics (Recommended Operating Conditions unless otherwise noted)
Parameter
Symbol
Test condition
Grade MIN. MAX. Unit Notes
Operating current
ICC1
Precharge standby current in ICC2P
Epower down mode
ICC2PS
Precharge standby current in ICC2N
non power down mode
O ICC2NS
Active standby current in
L power down mode
ICC3P
ICC3PS
Burst length = 1
tRC tRC (MIN.), IO = 0 mA
/CAS latency = 2
/CAS latency = 3
CKE VIL (MAX.), tCK = 15 ns
CKE VIL (MAX.), tCK =
CKE VIH (MIN.), tCK = 15 ns, /CS VIH (MIN.),
Input signals are changed one time during 30 ns.
CKE VIH (MIN.), tCK = ,
Input signals are stable.
CKE VIL (MAX.), tCK = 15 ns
CKE VIL (MAX.), tCK =
-A80
-A10
-A80
-A10
1,200 mA 1
1,200
1,200
1,200
259 mA
89
430 mA
152
295 mA
116
Active standby current in
ICC3N CKE VIH (MIN.), tCK = 15 ns, /CS VIH (MIN.),
520 mA
non power down mode
Input signals are changed one time during 30 ns.
ICC3NS CKE VIH (MIN.), tCK = ,
260
Input signals are stable.
P Operating current
ICC4 tCK tCK (MIN.), IO = 0 mA
/CAS latency = 2 -A80
1,380 mA 2
(Burst mode)
-A10
1,155
/CAS latency = 3 -A80
1,605
r -A10
1,425
CBR (Auto) Refresh current
ICC5
tRC tRC (MIN.)
/CAS latency = 2 -A80
2,370 mA 3
o -A10
2,370
/CAS latency = 3 -A80
2,370
-A10
2,370
d Self refresh current
ICC6 CKE 0.2 V
268 mA
Input leakage current
II (L) VI = 0 to 3.6 V, All other pins not under test = 0 V
–10 +10 µA
Output leakage current
IO (L) DOUT is disabled, VO = 0 to 3.6 V
–1.5 +1.5 µA
u High level output voltage
VOH IO = –4.0 mA
2.4
V
Low level output voltage
VOL IO = +4.0 mA
0.4 V
Notes 1. ICC1 depends on output loading and cycle rates. Specified values are obtained with the output open.
c In addition to this, ICC1 is measured on condition that addresses are changed only one time during tCK (MIN.).
2. ICC4 depends on output loading and cycle rates. Specified values are obtained with the output open.
t In addition to this, ICC4 is measured on condition that addresses are changed only one time during tCK (MIN.).
3. ICC5 is measured on condition that addresses are changed only one time during tCK (MIN.).
6
Data Sheet E0074N10
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]