MC-4516DA726EFC-A10 View Datasheet(PDF) - NEC => Renesas Technology

Part Name

Description

Manufacturer

MC-4516DA726EFC-A10

16 M-WORD BY 72-BIT SYNCHRONOUS DYNAMIC RAM MODULE REGISTERED TYPE

NEC => Renesas Technology 

MC-4516DA726

DC Characteristics (Recommended Operating Conditions unless otherwise noted)

Parameter

Symbol

Test condition

Grade MIN. MAX. Unit Notes

5

Operating current

ICC1 Burst length = 1

/CAS latency = 2 -A80

1,200 mA 1

5

tRC ≥ tRC (MIN.), IO = 0 mA

-A10

1,200

5

/CAS latency = 3 -A80

1,200

5

-A10

1,200

Precharge standby current in ICC2P CKE ≤ VIL (MAX.), tCK = 15 ns

259 mA

5

power down mode

ICC2PS CKE ≤ VIL (MAX.), tCK = ∞

89

Precharge standby current in ICC2N CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),

430 mA

non power down mode

Input signals are changed one time during 30 ns.

ICC2NS CKE ≥ VIH (MIN.), tCK = ∞ ,

152

Input signals are stable.

Active standby current in

ICC3P CKE ≤ VIL (MAX.), tCK = 15 ns

295 mA

power down mode

ICC3PS CKE ≤ VIL (MAX.), tCK = ∞

116

Active standby current in

ICC3N CKE ≥ VIH (MIN.), tCK = 15 ns, /CS ≥ VIH (MIN.),

520 mA

non power down mode

Input signals are changed one time during 30 ns.

ICC3NS CKE ≥ VIH (MIN.), tCK = ∞ ,

260

Input signals are stable.

Operating current

ICC4 tCK ≥ tCK (MIN.), IO = 0 mA

/CAS latency = 2 -A80

1,380 mA 2

(Burst mode)

-A10

1,155

/CAS latency = 3 -A80

1,605

-A10

1,425

5

CBR (Auto) Refresh current

ICC5

tRC ≥ tRC (MIN.)

/CAS latency = 2 -A80

2,370 mA 3

5

-A10

2,370

5

/CAS latency = 3 -A80

2,370

5

-A10

2,370

Self refresh current

ICC6 CKE ≤ 0.2 V

268 mA

Input leakage current

II (L) VI = 0 to 3.6 V, All other pins not under test = 0 V

–10 +10 µA

Output leakage current

IO (L) DOUT is disabled, VO = 0 to 3.6 V

–1.5 +1.5 µA

High level output voltage

VOH IO = –4.0 mA

2.4

V

Low level output voltage

VOL IO = +4.0 mA

0.4 V

Notes 1. ICC1 depends on output loading and cycle rates. Specified values are obtained with the output open.

In addition to this, ICC1 is measured on condition that addresses are changed only one time during tCK (MIN.).

2. ICC4 depends on output loading and cycle rates. Specified values are obtained with the output open.

In addition to this, ICC4 is measured on condition that addresses are changed only one time during tCK (MIN.).

3. ICC5 is measured on condition that addresses are changed only one time during tCK (MIN.).

6

Data Sheet M13203EJ7V0DS00

Share Link: