Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

MAX11209 View Datasheet(PDF) - Maxim Integrated

Part NameDescriptionManufacturer
MAX11209 18-Bit, Single-Channel, Ultra-Low-Power, DeltaSigma ADCs with Programmable Gain and GPIO MaximIC
Maxim Integrated MaximIC
MAX11209 Datasheet PDF : 27 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
MAX11209/MAX11211
18-Bit, Single-Channel, Ultra-Low-Power, Delta-
Sigma ADCs with Programmable Gain and GPIO
CTRL2: Control 2 Register
The byte-wide CTRL2 register is a bidirectional read/write register. The byte written to the CTRL2 register controls the
direction and values of the digital I/O ports.
Table 13. CTRL2 Register (Read/Write)
BIT
BIT NAME
DEFAULT
B7
DIR4
0
B6
DIR3
0
B5
DIR2
0
B4
DIR1
0
B3
DIO4
1
B2
DIO3
1
B1
DIO2
1
B0
DIO1
1
DIR[4:1]: The direction bits configure the direction of the DIO bit. When a DIR bit is set to 0, the associated DIO bit
is configured as an input and the value returned by a read of the DIO bit is the value being driven on the associated
GPIO. When a DIR bit is set to 1, the associated DIO bit is configured as an output and the GPIO port is driven to a
logic value of the associated DIO bit.
DIO[4:1]: The data input/output bits are bits associated with the GPIO ports. When a DIO is configured as an input,
the value read from the DIO bit is the logic value being driven at the GPIO port. When the direction is configured as an
output, the GPIO port is driven to a logic value associated with the DIO bit.
CTRL3: Control 3 Register
The byte-wide CTRL3 register is a bidirectional read/write register. The CTRL3 register controls the operation and
calibration of the device.
Table 14. CTRL3 Register (Read/Write)
BIT
BIT NAME
DEFAULT
B7
DGAIN2*
0
B6
DGAIN1*
0
B5
DGAIN0*
0
*These DGAIN_ bits are don’t-care bits for the MAX11209.
B4
NOSYSG
1
B3
NOSYSO
1
B2
NOSCG
1
B1
NOSCO
1
B0
RESERVED
0
DGAIN[2:0] (MAX11209 only): The digital gain bits control the input referred gain. With a gain of 1, the input range is
0 to VREF (unipolar) or ±VREF (bipolar). As the gain in increased by 2x, the input range is reduced to 0 to VREF/gain
or ±VREF/gain. Digital gain is applied to the final offset and gain-calibrated digital data. The DGAIN[2:0] bits decode
to digital gains as follows:
000 = 1
100 = 16
001 = 2
101 = 32
010 = 4
110 = 64
011 = 8
111 = 128
NOSYSG: The no-system gain bit, NOSYSG, controls the system gain calibration coefficient. A 1 in this bit location disables
the use of the system gain value when computing the final offset and gain corrected data value. A 0 in this location enables
the use of the system gain value when computing the final offset and gain corrected data value.
NOSYSO: The no system offset bit, NOSYSO, controls the system offset calibration coefficient. A 1 in this location disables
the use of the system offset value when computing the final offset and gain corrected data value. A 0 in this location enables
the use of the system offset value when computing the final offset and gain corrected data value.
NOSCG: The no self-calibration gain bit, NOSCG, controls the self-calibration gain calibration coefficient. A 1 in this location
disables the use of the self-calibration gain value when computing the final offset and gain corrected data value. A 0 in this
location enables the use of the self-calibration gain value when computing the final offset and gain corrected data value.
NOSCO: The no self-calibration offset bit, NOSCO, controls the use of the self-calibration offset calibration coefficient. A 1 in
this location disables the use of the self-calibration offset value when computing the final offset and gain corrected data value.
A 0 in this location enables the use of the self-calibration offset value when computing the final offset and gain corrected data
value.
20  
Maxim Integrated
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]