MAX11209 View Datasheet(PDF) - Maxim Integrated

Part Name

Description

Manufacturer

MAX11209

18-Bit, Single-Channel, Ultra-Low-Power, DeltaSigma ADCs with Programmable Gain and GPIO

Maxim Integrated 

MAX11209/MAX11211

18-Bit, Single-Channel, Ultra-Low-Power, Delta-

Sigma ADCs with Programmable Gain and GPIO

CS

SCLK

tCSS0

1

tDS

tDH

tCP

tCL

tCH

tDOT

tDOH

tDO1

8

9

tDOD

tCSS1

16

DIN X

HIGH-Z

RDY/DOUT

1

1

tDOE

X

RS3 RS2 RS1 RS0 W/R

X

X

X

X

X

X

X

X

D7

D6

D5 D4

D3

D2

D1

D0

HIGH-Z

Figure 7. SPI Register Access Read

Command Byte

Communication between the user and the device is con-

ducted through SPI using a command byte. The com-

mand byte consists of two modes differentiated as com-

mand modes and data modes. Command modes and

data modes are further differentiated by decoding the

remaining bits in the command byte. The mode selected

is determined by the MODE bit. If the MODE bit is 0, then

the user is requesting either a conversion, calibration, or

power-down; see Table 5. If the MODE bit is 1, then the

user is selecting a data command and can either read

from or write to a register; see Table 6.

The Status register (STAT1) is a read-only register and

provides general chip operational status to the user. If

the user attempts to calibrate the system and overranges

the internal signal scaling, then a gain overrange condi-

tion is flagged with the SYSOR bit. The last data rate

programmed for the ADC is available in the RATE bits.

If the input signal has exceeded positive or negative full

scale, this condition is flagged with the OR and UR bits.

If the modulator is busy converting, then the MSTAT bit

is set. If a conversion result is ready for readout, the RDY

bit is set; see Table 11.

The Control 1 register (CTRL1) is a read/write register,

and the bits determine the internal oscillator frequency,

unipolar or bipolar input range, selection of an internal or

external clock, enabling or disabling the reference and

input signal buffers, the output data format (offset binary

or two’s complement), and single-cycle or continuous

conversion mode. See Table 12.

The Control 2 register (CTRL2) is a read/write register,

and the bits configure the GPIOs as inputs or outputs

and their values. See Table 13.

The Control 3 register (CTRL3) is a read/write register,

and the bits determine the MAX11209 programmable

gain setting and the calibration register settings for both

the MAX11209 and MAX11211. See Table 14.

The Data register (DATA) is a read-only register. Data is

output from RDY/DOUT on the next 24 SCLK cycles once

CS is forced low. The data bits transition on the falling

edge of SCLK. Data is output MSB first, and is offset

binary or two’s complement, depending on the setting

of the FORMAT bit in the CTRL1 register. See Table 15.

The System Offset Calibration register (SOC) is a read/

write register, and the bits contain the digital value that

corrects the data for system zero scale. See Table 17.

The System Gain Calibration register (SGC) is a read/

write register, and the bits contain the digital value that

corrects the data for system full scale. See Table 18.

The Self-Cal Offset Calibration register (SCOC) is a read/

write register, and the bits contain the value that corrects

the data for chip zero scale. See Table 19.

The Self-Cal Gain Calibration register (SCGC) is a read/

write register, and the bits contain the value that corrects

the data for chip full scale. See Table 20.

Table 5. Command Byte (MODE = 0)

BIT

BIT NAME

B7

B6

START = 1 MODE = 0

B5

CAL1

B4

CAL0

B3

IMPD

B2

RATE2

B1

RATE1

B0

RATE0

Table 6. Command Byte (MODE = 1)

BIT

B7

B6

B5

BIT NAME START = 1 MODE = 1

0

B4

B3

B2

B1

B0

RS3

RS2

RS1

RS0

W/R

Note: The START bit is used to synchronize the data from the host device. The START bit is always 1.

Maxim Integrated

  15

Share Link: