M16C_62P View Datasheet(PDF) - Mitsumi
Part Name
Description
Manufacturer
M16C_62P Datasheet PDF : 349 Pages
| |||
Udenvdeelropment
SFR
Preliminary Specifications Rev.1.0
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M16C / 62P Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Address
000016
000116
000216
000316
000416
Processor mode register 0
Register
000516
000616
000716
000816
000916
000A16
000B16
000C16
000D16
000E16
000F16
001016
001116
001216
001316
001416
001516
001616
001716
001816
001916
001A16
001B16
001C16
001D16
001E16
001F16
002016
002116
002216
002316
002416
002516
002616
002716
002816
002916
002A16
002B16
002C16
002D16
002E16
002F16
003016
003116
003216
003316
003416
003516
003616
003716
003816
003916
003A16
003B16
003C16
003D16
003E16
003F16
Processor mode register 1
System clock control register 0
System clock control register 1
Chip select control register
Address match interrupt enable register
Protect register
Data bank register
Oscillation stop detection register
Watchdog timer start register
Watchdog timer control register
Address match interrupt register 0
Address match interrupt register 1
Power supply detection register 1
Power supply detection register 2
Chip select expansion control register
PLL control register 0
Processor mode register 2
Power supply down detection interrupt register
DMA0 source pointer
DMA0 destination pointer
DMA0 transfer counter
DMA0 control register
DMA1 source pointer
DMA1 destination pointer
DMA1 transfer counter
DMA1 control register
Symbol
After reset
(Note 2)
(Note 3)
PM0
PM1
CM0
CM1
CSR
AIER
PRCR
DBR
CM2
WDTS
WDC
RMAD0
RMAD1
000000002(CNVSS pin is “L”)
000000112(CNVSS pin is “H”)
000010002
010010002
001000002
000000012
XXXXXX002
XX0000002
0016
0000X0002
??16
00??????2(Note 4)
0016
0016
X016
0016
0016
X016
(Note 5)
(Note 5)
VCR1
VCR2
CSE
PLC0
PM2
D4INT
SAR0
DAR0
TCR0
000010002
0016
0016
0001X0102
XXX000002
0016
??16
??16
X?16
??16
??16
X?16
??16
??16
DM0CON
00000?002
SAR1
DAR1
TCR1
DM1CON
??16
??16
X?16
??16
??16
X?16
??16
??16
00000?002
Note 1: The blank areas are reserved and cannot be used by users.
Note 2: The PM00 and PM01 bits do not change at software reset, watchdog timer reset and oscillation stop detection reset.
Note 3: The CM20, CM21, and CM27 bits do not change at oscillation stop detection reset.
Note 4: The WDC5 bit is “0” (cold start) immediately after power-on. It can only be set to “1” in a program. It is set to “0” when the input voltage
at the VCC1 pin drops to Vdet2 or less while the VC25 bit in the VCR2 register is set to “1” (RAM retention limit detection circuit enable
Note 5: This register does not change at software reset, watchdog timer reset and oscillation stop detection reset.
X : Nothing is mapped to this bit
? : Undefined
14
|
|
Share Link: 