Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

M16C64C View Datasheet(PDF) - Renesas Electronics

Part NameDescriptionManufacturer
M16C64C SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Renesas
Renesas Electronics Renesas
M16C64C Datasheet PDF : 91 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
M16C/64C Group
1. Overview
1.6 Pin Functions
Table 1.7 Pin Functions for the 100-Pin Package (1/3)
Signal Name Pin Name I/O Power Supply
Description
Power supply
input
VCC1,
VCC2, VSS
I
-
Apply 2.7 to 5.5 V to pins VCC1 and VCC2 (VCC1 VCC2)
and 0 V to the VSS pin.
Analog power
supply input
AVCC, AVSS I
VCC1
This is the power supply for the A/D and D/A converters.
Connect the AVCC pin to VCC1, and connect the AVSS pin
to VSS.
Reset input
RESET
I
VCC1 Driving this pin low resets the MCU.
CNVSS
CNVSS
I
External data bus
width select input
BYTE
I
D0 to D7 I/O
VCC1
VCC1
VCC2
Input pin to switch processor modes. After a reset, to start
operating in single-chip mode, connect the CNVSS pin to
VSS via a resistor. To start operating in microprocessor
mode, connect the pin to VCC1.
Input pin to select the data bus of the external area. The data
bus is 16 bits when it is low, and 8 bits when it is high. This
pin must be fixed either high or low. Connect the BYTE pin to
VSS in single-chip mode.
Inputs or outputs data (D0 to D7) while accessing an
external area with a separate bus.
D8 to D15 I/O
VCC2
Inputs or outputs data (D8 to D15) while accessing an
external area with a 16-bit separate bus.
A0 to A19
O
A0/D0 to
A7/D7
I/O
A1/D0 to
A8/D7
I/O
CS0 to CS3 O
Bus control pins
WRL/WR
WRH/BHE O
RD
ALE
O
HOLD
I
HLDA
O
RDY
I
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
Outputs address bits A0 to A19.
Inputs or outputs data (D0 to D7) and outputs address bits
(A0 to A7) by timesharing, while accessing an external area
with an 8-bit multiplexed bus.
Inputs or outputs data (D0 to D7) and outputs address bits
(A1 to A8) by timesharing, while accessing an external area
with a 16-bit multiplexed bus.
Outputs chip-select signals CS0 to CS3 to specify an
external area.
Outputs WRL, WRH, (WR, BHE), and RD signals. WRL and
WRH can be switched with BHE and WR.
WRL, WRH, and RD selected
If the external data bus is 16 bits, data is written to an even
address in an external area when WRL is driven low. Data
is written to an odd address when WRH is driven low. Data
is read when RD is driven low.
WR, BHE, and RD selected
Data is written to an external area when WR is driven low.
Data in an external area is read when RD is driven low. An
odd address is accessed when BHE is driven low. Select
WR, BHE, and RD when using an 8-bit external data bus.
Outputs an ALE signal to latch the address.
HOLD input is unavailable. Connect the HOLD pin to VCC2
via a resistor (pull-up).
In a hold state, HLDA outputs a low-level signal.
The MCU bus is placed in a wait state while the RDY pin is
driven low.
Power supply: VCC2 is used to supply power to the external bus associated pins. The dual power supply configuration
allows VCC2 to interface at a different voltage than VCC1.
R01DS0016EJ0100 Rev.1.00
Feb 07, 2011
Page 11 of 88
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2020  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]