Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

M16C30M8 View Datasheet(PDF) - Renesas Electronics

Part NameDescriptionManufacturer
M16C30M8 SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER Renesas
Renesas Electronics Renesas
M16C30M8 Datasheet PDF : 166 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Pin Description
Mitsubishi microcomputers
M16C / 30L Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Pin Description
Pin name Signal name I/O type
Function
P50 to P57 I/O port P5
Input/output This is an 8-bit I/O port equivalent to P0. In single-chip mode, P57 in
this port outputs a divide-by-8 or divide-by-32 clock of XIN or a clock of
the same frequency as XCIN as selected by software.
WRL / WR,
WRH / BHE,
RD,
BCLK,
HLDA,
HOLD,
ALE,
RDY
P60 to P67 I/O port P6
Output
Output
Output
Output
Output
Input
Output
Input
Output WRL, WRH (WR and BHE), RD, BCLK, HLDA, and ALE
signals. WRL and WRH, and BHE and WR can be switched using
software control.
WRL, WRH, and RD selected
With a 16-bit external data bus, data is written to even addresses
when the WRL signal is “L” and to the odd addresses when the WRH
signal is “L”. Data is read when RD is “L”.
WR, BHE, and RD selected
Data is written when WR is “L”. Data is read when RD is “L”. Odd
addresses are accessed when BHE is “L”. Use this mode when using
an 8-bit external data bus.
While the input level at the HOLD pin is “L”, the microcomputer is
placed in the hold state. While in the hold state, HLDA outputs a “L”
level. ALE is used to latch the address. While the input level of the
RDY pin is “L”, the microcomputer is in the ready state.
Input/output
This is an 8-bit I/O port equivalent to P0. When used for input in single-
chip, memory expansion, and microprocessor modes, the port can be
set to have or not have a pull-up resistor in units of four bits by
software. Pins in this port also function as UART0 and UART1 I/O pins
as selected by software.
P70 to P77
I/O port P7
Input/output This is an 8-bit I/O port equivalent to P6 (P70 and P71 are N channel
open-drain output). Pins in this port also function as timer A0–A2, or
UART2 I/O pins as selected by software.
P80 to P84,
P86,
P87,
P85
I/O port P8
I/O port P85
Input/output
Input/output
Input/output
Input
P80 to P84, P86, and P87 are I/O ports with the same functions as P6.
Using software, they can be made to function as the I/O pins for the
input pins for external interrupts. P86 and P87 can be set using
software to function as the I/O pins for a sub clock generation
circuit. In this case, connect a quartz oscillator between P86 (XCOUT
pin) and P87 (XCIN pin). P85 is an input-only port that also functions
for NMI. The NMI interrupt is generated when the input at this pin
changes from “H” to “L”. The NMI function cannot be cancelled using
software. The pull-up cannot be set for this pin.
P90 to P97 I/O port P9
P100 to P107 I/O port P10
Input/output This is an 8-bit I/O port equivalent to P6. Pins in this port also function
as, timer B1, B2 input pins, A-D converter extended input pins, or A-D
trigger input pins as selected by software.
Input/output This is an 8-bit I/O port equivalent to P6. Pins in this port also function
as A-D converter input pins as selected by software. Furthermore, P104
–P107 also function as input pins for the key input interrupt function.
9
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2020  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]