Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

6295CV Просмотр технического описания (PDF) - Intersil

Номер в каталогеКомпоненты Описаниепроизводитель
6295CV Low Voltage Fuel Gauge Intersil
Intersil Intersil
6295CV Datasheet PDF : 25 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL6295
Absolute Maximum Ratings
Supply Voltage VP . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 10V
Input Voltage or IO Voltage . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V
Recommended Operating Conditions
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . .-20°C to 85°C
Operating Supply Voltage (VP Pin) . . . . . . . . . . . . . . . . . 2.8V to 7V
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
Maximum Junction Temperature (Plastic Package) . . . . . . . . 120°C
Maximum Storage Temperature Range . . . . . . . . . . . -35°C to 120°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Typical Values Are Tested at VP = 5V and ambient temperature is at 25°C, All Maximum and Minimum Values
Are Guaranteed Under the Recommended Operating Conditions., Unless Otherwise Noted.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX UNITS
DC CHARACTERISTICS
Supply Voltage
VP
For SMBus and register access
2.8
For EEPROM write
3.3
7.0
V
7.0
V
For guaranteed analog parametrics
3.0
7.0
V
Supply Current Run Mode
Supply Current Sample Mode
Supply Current Sample - Sleep Mode
Supply Current Shelf Sleep Mode
Input Low Voltage IO0, IO1
Input High Voltage IO0, IO1
GPIO Input Low Current Pull-up mode
Leakage Current IO pin programmed
as outputs or inputs without pullup
IDD
IDDINS
IDDSLP
IDDSSLP
VIL
VIH
IIL-IO0PU
IL-IO
A/D Active (Note 1)
A/D Inactive (Notes 1, 2)
Sample -Sleep Mode (Note 1)
Shelf Sleep Mode (Note 1)
85
120
µA
45
85
µA
20
40
µA
400
800
nA
0.6
V
2.4
V
7
µA
1
600
nA
Output low voltage for IO0, IO1
Output high voltage for IO0 configured
as push-pull
VOL-IO
VOH-IO
IOL = 0.5mA
IOH = 100µA
0.4
V
2.1
V
Thermistor Output Current
INTC
ROSC = 221k± 0.1%
Input Low Voltage for SMBus pins
VIL-SMB
Input High Voltage for SMBus pins
VIH-SMB
Output Low Voltage for SMBus pins
VOL-SMB IPULLUP = 4mA
Output High Voltage for SMBus pins
VOH-SMB (Note 3)
Input leakage current SMBus pins
ILEAK-SMB
AC CHARACTERISTICS (TA = -20°C to +85°C; VP = 3.0V to 7.0V; ROSC = 221k± 0.1%)
Internal main oscillator frequency
fRC
ROSC = 221k± 0.1%
Internal auxiliary oscillator frequency
fAUX
Accumulator Time Base Accuracy
(internal 2Hz clock)
fACC
During Run and Sample mode
(Note 3)
8
2.0
2.1
-5.0
130.8
118
-0.6
13
16
µA
0.8
V
5.5
V
0.4
V
5.5
V
+5.0
µA
131.5
131
132.2
kHz
144
kHz
+0.6
%
During Sample-Sleep mode (Note 3)
-10
+10
%
Internal A/D operating clock
fA/D
(Note 3)
fRC/4
kHz
Power-on-Reset Threshold
Delay to entry of Shelf-Sleep mode
VPOR
Voltage at VP
2.4
tSHELF
(Shent = 1 or VP < VPtrip) and (SDA
and SCL go low)
2.75
V
10
ms
2
FN9074.0
October 25, 2005
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]