DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

ISL22343UFV20Z-TK View Datasheet(PDF) - Intersil

Part Name
Description
Manufacturer
ISL22343UFV20Z-TK Datasheet PDF : 19 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ISL22343
Operating Specifications Over the recommended operating conditions unless otherwise specified. (Continued)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(Note 21) (Note 5) (Note 21) UNIT
Cb
Capacitive Loading of SDA Total on-chip and off-chip
(Note 19) or SCL
10
400
pF
Rpu
SDA and SCL Bus Pull-up Maximum is determined by tR and tF
1
k
(Note 19) Resistor Off-chip
For Cb = 400pF, max is about 2~2.5k
For Cb = 40pF, max is about 15~20k
tSU:A
A1 and A0 Setup Time
Before START condition
600
ns
tHD:A A1 and A0 Hold Time
After STOP condition
600
ns
NOTES:
5. Typical values are for TA = +25°C and 3.3V supply voltage.
6. LSB: [V(RW)255 – V(RW)0]/255. V(RW)255 and V(RW)0 are V(RW) for the DCP register set to FF hex and 00 hex respectively. LSB is the
incremental voltage when changing from one tap to an adjacent tap.
7. ZS error = V(RW)0/LSB.
8. FS error = [V(RW)255 – VCC]/LSB.
9. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 255. i is the DCP register setting.
10. INL = [V(RW)i – i • LSB – V(RW)0]/LSB for i = 1 to 255.
11. VMATCH= [V(RWx)i -V(RWy)i]/LSB, for i = 0 to 255, x = 0 to 3, y = 0 to 3.
12.
TCV
=
-------M-----a----x------V-------R-----W--------i-----–-----M-----i--n------V-------R-----W--------i--------
MaxVRWi+ MinVRWi  2
+1----61---50----°6--C---
for i = 16 to 240 decimal,
voltage and Min ( ) is the
T = -40°C to +125°C.
minimum value of the
Max( ) is the maximum value of the wiper
wiper voltage over the temperature range.
13. MI = |RW255 – RW0|/255. MI is a minimum increment. RW255 and RW0 are the measured resistances for the DCP register set to FF hex and
00 hex respectively.
14. Roffset = RW0/MI, when measuring between RW and RL.
Roffset = RW255/MI, when measuring between RW and RH.
15. RDNL = (RWi – RWi-1)/MI -1, for i = 16 to 255.
16. RINL = [RWi – (MI • i) – RW0]/MI, for i = 16 to 255.
17. RMATCH= [(Rx)i -(Ry)i]/MI, for i = 0 to 255, x = 0 to 3, y = 0 to 3.
18.
TCR
=
-------M-----a----x------R-----i-----–-----M-----i--n------R-----i--------
MaxRi+ MinRi  2
+1----61---5-0---°6--C---
for i = 16 to 240, T = -40°C to +125°C. Max( ) is the maximum value of
the minimum value of the resistance over the temperature range.
the resistance and
Min ( ) is
19. This parameter is not 100% tested.
20. tWC is the time from a valid STOP condition at the end of a Write sequence of I2C serial interface, to the end of the self-timed internal non-
volatile write cycle.
21. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.
8
FN6423.2
August 17, 2015
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]