ISL12058IRTZ-T View Datasheet(PDF) - Intersil
Part Name
Description
Manufacturer
ISL12058IRTZ-T Datasheet PDF : 19 Pages
| |||
ISL12058
TABLE 4. FUNCTION SELECTION OF IRQ/FOUT PIN WITH
A1E AND IRQE BITS (Continued)
A1E IRQE
1
0
1
1
IRQ/FOUT FUNCTION
FOUT
Alarm 1 Interrupt
FREQUENCY OUT CONTROL BITS (FO <1:0>)
These bits select the output frequency at the IRQ/FOUT pin.
IRQE must be set to “0” for frequency output at the
IRQ/FOUT pin. Refer to Table 5 for frequency selection.
TABLE 5. FREQUENCY SELECTION OF IRQ/FOUT PIN WITH
FO1 AND FO0 BITS
FREQUENCY,
FO1
FO0
FOUT (Hz)
COMMENT
1
1
32768
Free running crystal clock
1
0
8192
Free running crystal clock
0
1
4096
Free running crystal clock
0
0
1
Sync. at RTC write
ALARM ENABLE BITS (ALM1E, ALM2E)
This bit enables/disables the Alarm1 and Alarm2 function.
When the ALM1E bit is set to “1”, the Alarm1 function is
enabled. When the ALM1E is cleared to “0”, the alarm function
is disabled. ALM1E bit is set to “0” at power-up.
When the ALM2E bit is set to “1”, the Alarm2 function is
enabled. When the ALM2E is cleared to “0”, the alarm function
is disabled. ALM2E bit is set to “0” at power-up.
NOTE: The Alarm1 has hardware function via the IRQ/FOUT pin.
Alarm2 does not have hardware interrupt function.
Alarm1 Registers
Addresses [Address 0Ch to 11h]
The Alarm1 register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte functions as
an enable bit (enable = “1”). These enable bits specify which
alarm registers (seconds, minutes, etc) are used to make the
comparison. Note that there is no alarm byte for year. When
all the enable bits are set to “0” with ALM1E set to “1”, the
Alarm 1 will triggered once a second.
The Alarm1 function works as a comparison between the
Alarm1 registers and the RTC registers. As the RTC
advances, the Alarm1 will be triggered once a match occurs
between the Alarm1 registers and the RTC registers. Any
one Alarm1 register, multiple registers, or all registers can be
enabled for a match.
To clear an Alarm1, the A1F status bit can be set to “0” with a
write or use the ARST bit auto reset function.
TABLE 6. ALARM1 INTERRUPT WITH ENABLE BITS SELECTION
A1M1 A1M2 A1M3 A1M4 A1M5 A1M6
ALARM1
Interrupt
0
0
0
0
0
0
Every Second
1
0
0
0
0
0
Match Second
0
1
0
0
0
0
Match Minute
0
0
1
0
0
0
Match Hour
0
0
0
1
0
0
Match Date
0
0
0
0
1
0
Match Month
0
0
0
0
0
1
Match Day
1
1
0
0
0
0
Match Second
and Minute
1
0
1
0
0
0
Match Second
and Hour
1
1
1
0
0
0 Match Second,
Minute, and Hour
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
0
0
0
1
1
1
Match Date,
Month, and Day
1
0
0
1
1
1 Match Second,
Date, Month, and
Day
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
0
1
1
1
1
1
Match MInute,
Hour, Date,
Month, and Day
1
1
1
1
1
1 Match Second,
MInute, Hour,
Date, Month, and
Day
Following is example of Alarm1 Interrupt.
Example – A single alarm will occur on January 1 at
11:30am.
A. Set Alarm1 registers as follows:
11
FN6756.0
June 15, 2009
|
|
Share Link: 