ILC7082ADJ View Datasheet(PDF) - Fairchild Semiconductor
Part Name
Description
Manufacturer
ILC7082ADJ Datasheet PDF : 16 Pages
| |||
ILC7082
Electrical Characteristics ILC7082AIM5
Unless otherwise specified, all limits are at TA=25°C; VIN = VOUT(NOM) +1V, ΙOUT = 1mA, COUT = 1µF, VON/OFF = 2V.
Boldface type denotes specifications which apply over the specified operating temperature range.
Parameter
Input Voltage Range
Output Voltage
Feedback Voltage
(ADJ version)
Line Regulation
Dropout Voltage
(Note 3)
Symbol
VIN
VOUT
VADJ
∆VOUT/
(VOUT*∆VIN)
VDO
Ground Pin Current
IGND
Shutdown (OFF) Current
ON/OFF Input Voltage
ON/OFF Pin Input
Current
Peak Output Current
(Note 4)
Output Noise Voltage
(RMS)
ION/OFF
VON/OFF
IIN(ON/OFF)
IOUT(peak)
eN
Ripple Rejection
∆VOUT/∆VIN
Dynamic Line Regulation ∆VOUT(line)
Dynamic Load Regulation ∆VOUT(load)
Short Circuit Current
ISC
Conditions
1mA < IOUT < 150mA
1mA < IOUT < 150mA
VOUT(NOM) +1V < VIN < 12V
Min
2
-1
-1
-2
1.215
1.202
IOUT= 0mA (Note 4)
IOUT = 10mA
IOUT = 50mA
IOUT = 100mA
IOUT = 150mA
IOUT = 0mA
IOUT = 10mA
IOUT = 50mA
IOUT = 100mA
IOUT = 150mA
VON/OFF = 0V
High = Regulator On
1.5
Low = Regulator Off
VON/OFF = 0.6V, regulator OFF
VON/OFF = 2V, regulator ON
VOUT > 0.95VOUT(NOM),
400
tpw = 2ms
BW = 300Hz to 50kHz, CIN = 1µF
CNOISE = 0.01µF, COUT = 2.2µF,
IOUT = 10mA
COUT = 4.7µF, Freq. = 1kHz
IOUT = 100mA Freq. = 10kHz
Freq. = 1MHz
VIN: VOUT(NOM) + 1V to
VOUT(NOM) + 2V,
tr, tf = 2µs; IOUT = 150mA
IOUT: 1mA to 150mA; tr, tf = 10µS
VOUT = 0V
Typ
VOUT(NOM)
VOUT(NOM)
1.240
0.007
0.1
10
50
100
150
95
100
100
100
115
0.1
0.3
1
500
40
85
70
60
14
40
600
Max Units
13
V
+1 %VOUT
+1
(NOTM)
+2
1.265 V
1.278
0.014 %/V
0.032
1
mV
2
25
35
75
100
150
200
225
300
200 µA
220
220
240
220
240
240
260
260
280
2
µA
V
0.6
µA
mA
µVRMS
dB
mV
mV
mA
Notes:
1. Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical
specifications do not apply when operating the device outside of its rated operating conditions.
2. Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods.
Measurements are taken at constant junction temperature as close to ambient as possible using low duty pulse testing.
3. Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the nominal
value measured with an IV differential.
4. Guaranteed by design
4
REV. 1.6.2 11/17/04
|
|
Share Link: 