DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

HCPL-0302-060E View Datasheet(PDF) - Avago Technologies

Part Name
Description
Manufacturer
HCPL-0302-060E
AVAGO
Avago Technologies AVAGO
HCPL-0302-060E Datasheet PDF : 15 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Package Characteristics
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Symbol Min. Typ. Max. Units
VISO
3750
Vrms
Test Conditions
Fig. Note
TA = 25°C, RH < 50%
8, 9
RI-O
1012
VI-O = 500 V
9
CI-O
0.6
pF
Freq = 1 MHz
Notes:
1. Derate linearly above 70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
minimum = 0.2 A. See Application section for additional details on limiting IOL peak.
3. Derate linearly above 85°C, free air temperature at the rate of 4.0 mW/°C.
4. Input power dissipation does not require derating.
5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%.
6. In this test, VOH is measured with a DC load current. When driving capacitive load VOH will approach VCC as IOH approaches zero amps.
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage >4500 Vrms for 1 second (leakage detec-
tion current limit II-O < 5 µA). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN
60747-5-2 Insulation Characteristics Table, if applicable.
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. PDD is the difference between tPHL and tPLH between any two parts or channels under the same test conditions.
11. Common mode transient immunity in the high state is the maximum tolerable |dVCM/dt| of the common mode pulse VCM to assure that the
output will remain in the high state (i.e. VO > 6.0 V).
12. Common mode transient immunity in a low state is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that the output
will remain in a low state (i.e. VO < 1.0 V).
13. This load condition approximates the gate load of a 1200 V/20 A IGBT.
14. The power supply current increases when operating frequency and Cg of the driven IGBT increases.
0
-0.5
-1.0
-1.5
-2.0
-2.5
-50 -25 0 25 50 75 100 125
TA – TEMPERATURE – C
Figure 1. VOH vs. temperature.
0
0.44
0.43
-1
0.42
-2
0.41
-3
0.40
-4
0
0.2
0.4
IOH – OUTPUT HIGH CURRENT – A
Figure 2. VOH vs. IOH.
0.39
-50 -25 0 25 50 75 100 125
TA – TEMPERATURE – C
Figure 3. VOL vs. temperature.

 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]