E114I View Datasheet(PDF) - MicroPower Direct, LLC
Part Name
Description
Manufacturer
E114I Datasheet PDF : 2 Pages
| |||
E100I Series
High Isolation
Miniature, 1W SIP
DC/DC Converters
New Models!!
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 1W Output Power
• Miniature SIP Case
• 3,000 VDC Isolation
• Complies to RFI Standards
Input
Parameter
Input Voltage Range
Conditions
5 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
Min.
4.5
10.8
21.6
43.2
Typ.
5.0
12.0
24.0
48.0
Max.
5.5
13.2
26.4
52.8
Units
VDC
• >2 MHour MTBF
Reverse Polarity Input Current
0.3
A
• 20 Standard Models
• Industry Standard Pin-Out
Input Filter
Output
Parameter
Conditions
Internal Capacitor
Min. Typ. Max.
Units
Output Voltage Accuracy
±3.0
%
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation (Note 1)
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
60
mV P - P
Output Power Protection
110
%
Temperature Coefficient
±0.01 ±0.02 %/ºC
Output Short Circuit
RoHS Compliant General
Momentary (0.5 Sec.)
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VDC
Isolation Resistance
1,000 VDC 1,000
MΩ
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
50
kHz
EMI/RFI
EN55022 A, EN55024 A, IEC 61000-4-2, IEC 61000-4-3, FCC 47 CFR Part 15 B
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case
+100
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
Weight
0.46 x 0.24 x 0.40 Inches (11.68 x 6.0 x 10.2 mm)
0.46 x 0.29 x 0.40 Inches (11.68 x 7.5 x 10.2 mm)
Non-Conductive Black Plastic (UL94-V0)
0.06 Oz (1.8g)
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
Units
MHours
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
7.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
24 VDC Input -0.7
15.0
VDC
28.0
48 VDC Input -0.7
54.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Internal Power Dissipation
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
|
|
Share Link: 