DatasheetQ Logo
Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

DM111E View Datasheet(PDF) - MicroPower Direct, LLC

Part Name
Description
Manufacturer
DM111E Datasheet PDF : 2 Pages
1 2
Model Selection Guide
www.micropowerdirect.com
Model
Number
DM101E
DM102E
DM103E
DM104E
DM105E
DM106E
DM111E
DM112E
DM113E
DM114E
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
273
30
5
4.5 - 5.5
270
30
5
4.5 - 5.5
263
30
5
4.5 - 5.5
278
30
5
4.5 - 5.5
256
30
5
4.5 - 5.5
256
30
12 10.8 - 13.2 107
15
12 10.8 - 13.2 103
15
12 10.8 - 13.2 105
15
12 10.8 - 13.2 114
15
Voltage
(VDC)
5.0
12.0
15.0
±5.0
±12.0
±15.0
5.0
12.0
15.0
±5.0
Output
Current
(mA, Max)
200.0
83.0
67.0
±100.0
±42.0
±33.0
200.0
83.0
67.0
±100.0
Current
(mA, Min)
20.0
9.0
7.0
±10.0
±5.0
±4.0
20.0
9.0
7.0
±10.0
Load
Regulation
(%, Max)
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
15
73
500
15
74
500
15
76
500
15
72
500
15
78
500
15
78
500
15
78
200
15
81
200
15
79
200
15
73
200
DM115E
12 10.8 - 13.2 105
15
±12.0
±42.0
±5.0
15
79
200
DM116E
12 10.8 - 13.2 105
15
±15.0
±33.0
±4.0
15
79
200
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters will operate without external components. However,
when measuring output ripple, it is recommended that an external ce-
ramic capacitor be placed from the +Vout pin to the -Vout pin for single
output units and from each output to common for dual output units. An
input capacitor will enhace stability over temperature and input line
variations. Recommended capacitor values are given in the table above.
For applications requiring very low output noise levels, a simple LC filter
should be effective.
Vin
Input
Capacitor
Vout
Output Capacitor
Single Dual
5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF
12 VDC 2.2 µF 12 VDC 2.2 µF 1.0 µF
15 VDC 1.0 µF 0.47 µF
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC
output. To do this, connect the load across the positive (+Vout) and
negative (-Vout) outputs and float the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin Single Dual Pin
1 +Vin +Vin
5
2 -Vin -Vin
6
4 -Vout -Vout
Single
No Pin
+Vout
Dual
Common
+Vout
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the
side of the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com
 

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]