Electronic component search and free download site.
Transistors,MosFET ,Diode,Integrated circuits

D105ER Ver la hoja de datos (PDF) - MicroPower Direct, LLC

Número de piezacomponentes DescripciónFabricante
D105ER Low Cost, 1W SIP Tightly Regulated DC/DC Converters MPD
MicroPower Direct, LLC MPD
D105ER Datasheet PDF : 2 Pages
1 2
Model Selection Guide
Input
Output
Model
Number
Voltage (VDC)
Current (mA)
Voltage Current
Efficiency
Current (%, Typ)
Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min)
D101ER
5
4.75 - 5.25 294
30
5.0
200.0
20.0
68
D102ER
5
4.75 - 5.25 286
30
9.0
111.0
12.0
70
D103ER
5
4.75 - 5.25 282
30
12.0
83.0
9.0
71
D104ER
5
4.75 - 5.25 278
30
15.0
67.0
7.0
72
D105ER
5
4.75 - 5.25 290
30
±5.0 ±100.0
±10.0
69
D106ER
5
4.75 - 5.25 286
30
±9.0
±56.0
±6.0
70
D107ER
5
4.75 - 5.25 278
30
±12.0
±42.0
±5.0
72
D108ER
5
4.75 - 5.25 278
30
±15.0
±33.0
±4.0
72
D111ER
12
11.4 - 12.6
121
15
5.0
150.0
15.0
69
D112ER
12
11.4 - 12.6
117
15
9.0
111.0
12.0
71
D113ER
12
11.4 - 12.6
116
15
12.0
83.0
9.0
72
D114ER
12
11.4 - 12.6
116
15
15.0
67.0
7.0
72
D115ER
12
11.4 - 12.6
119
15
±5.0 ±100.0
±10.0
70
D116ER
12
11.4 - 12.6
116
15
±9.0
±56.0
±6.0
72
D117ER
12
11.4 - 12.6
114
15
±12.0
±42.0
±5.0
73
D118ER
12
11.4 - 12.6
114
15
±15.0
±33.0
±4.0
73
D121ER
24 22.8 - 25.2
59
8
5.0
150.0
15.0
70
D122ER
24 22.8 - 25.2
58
8
9.0
111.0
12.0
72
D123ER
24 22.8 - 25.2
57
8
12.0
83.0
9.0
73
D124ER
24 22.8 - 25.2
57
8
15.0
67.0
7.0
73
D125ER
24 22.8 - 25.2
58
8
±5.0 ±100.0
±10.0
72
D126ER
24 22.8 - 25.2
58
8
±9.0
±56.0
±6.0
72
D127ER
24 22.8 - 25.2
57
8
±12.0
±42.0
±5.0
73
D128ER
24 22.8 - 25.2
57
8
±15.0
±33.0
±4.0
73
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters will operate without external components. However, when
measuring output ripple, it is recommended that an external ceramic capaci-
tor be placed from the +Vout pin to the -Vout pin for single output units
and from each output to common for dual output units. An input capacitor
will enhace stability
over temperature and
input line variations.
Recommended capaci-
tor values are given in
Vin
5 VDC
Input
Capacitor
4.7 μF
Vout
5 VDC
Output Capacitor
Single Dual
10.0 μF 4.7 μF
the table at right. For 12 VDC 2.2 μF 9 VDC 4.7 μF 2.2 μF
applications requir- 24 VDC
ing very low output
noise levels, a simple
1.0 μF
12 VDC 2.2 μF 1.0 μF
15 VDC 1.0 μF 0.47 μF
LC filter should be effective.
4. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
100
100
100
100
100
100
100
100
Mechanical Dimensions (Single Output) Mechanical Dimensions (Dual Output)
Pin
Connections
Pin Single Dual
1 +Vin +Vin
2 -Vin -Vin
4 -Vout No Pin
6 +Vout No Pin
7 No Pin +Vout
9 No Pin -Vout
10 No Pin Common
MicroPower Direct
www.micropowerdirect.com
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation
on the side of the unit
292 Page Street, STE D, Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com
Direct download click here

 

Share Link : 
All Rights Reserved© datasheetq.com 2015 - 2019  ] [ Privacy Policy ] [ Request Datasheet  ] [ Contact Us ]